Fisher & Paykel NZ AU PAC SG Controlled cold, End of cycle beeps, Auto water fill level

Page 27

Changing pre-set options

Controlled cold

25

WashSmart™ model only

If your cold water temperature is very low you will not get a very effective wash. The CONTROLLED COLD option solves this problem by adding a small amount of hot water to raise the temperature of the wash to approximately 20°C. We have called this “CONTROLLED COLD”.

1When in option adjustment mode, select COLD wash temperature.

2The wash progress lights show the temperature adjustment possible.

■■When the first progress light (from the left) is on, the machine will fill with cold water only.

■■Press the ADVANCE button to select the second light (from the left) and your washer will control the temperature to approximately 20°C. Each following light approximately equals a 1°C temperature rise.

Note: if you always use COLD or CONTROLLED COLD water, we recommend that a WARM or HOT wash be used regularly, eg every 5th wash should be at least a warm one.

Fig.37 Changing the cold wash temperature setting

End of cycle beeps

WashSmart™ model only

The beeps signalling the end of the cycle can be increased or decreased. Press the options button to increase the number of beeps or press again for no beeps to sound at the end of the cycle.

Auto water fill level

WashSmart™ model only

If you are not satisfied with the level that your washer fills to on AUTO water level, you can increase or decrease the fill level that AUTO will select.

Note: if you feel there is not enough water for the load, we recommend you check by pausing the machine and pushing the clothes down to see how much spare water is at the bottom of the bowl. Clothes often float and your washer can sense the water under the clothes.

Light on

Option

FAVOURITE

less water

 

 

EASY IRON

factory setting

 

 

ALLERGY

more water +

 

 

HAND WASH

more water ++

 

 

HEAVY DUTY

more water +++

 

 

Image 27
Contents Installation instructions Intelligence working for you Contents Drain hose Installation instructionsUnpacking LocationCold supply only Inlet hose replacementInlet hoses Levelling your machineDraining Clothes washer safetyAccessories and spare parts Water supplyBefore you do your first wash Getting startedUsing your WashSmart washer DetergentFabric softener Advance If you wish to stop your WashSmart washerWash cycles Wash optionsWA65T60M MW613, MW60, WA55T56M MW513, WA75T56M MWC12 Using your QuickSmart washerIf you wish to stop your QuickSmart washer PowerLID Locked light Lid lockDefault settings Model variationsBasic cycle descriptions Wash progress lights Clothes care safeguardsWash options and advancing the cycle To select the wash optionsWater levels Manual water level selectionAuto water level Quick wash Wash options saving water and timeNappy sanitisers/bleach Delay StartWash options SoakWashing woollens Washing bulky itemsTo use your favourite cycle Favourite cycleFavourite cycle To set your favourite cycleTo customise a cycle Customising the wash cyclesLint givers Lint collectors Before you washSorting LoadingAdding the detergent DetergentChoosing the right detergent How much detergent?How much fabric softener? Cleaning the dispenserFabric softener How the fabric softener is dispensedOption adjustment mode To enter option adjustment modeChanging pre-set options Use the buttons on the panel to change the pre-set options Rinse options Wash temperaturesLight on Option Controlled coldEnd of cycle beeps Auto water fill levelSpecifications Out of balance recovery routineMachine information Caring for your washer When you have finishedCleaning your washer Cleaning the inside of your washerAutomatic lint system Washer sounds and beepsRecycling the water from a deep rinse Saving waterWater saving tips Recycling the wash waterReturn Hose to Drain Manual suds save with syphon backHigh water level light is flashing HOT water temperature light is flashingCold water temperature light is flashing HOT and Cold water temperature lights are flashingSome lights are on but the pattern of lights is unfamiliar Single beep every second and... possible solutionsIf your washer beeps for help LID Locked light is flashingOperating problems Wash problems Tangling Dye transferManufacturer’s Warranty Fisher & Paykel undertakes toThese warranties do not cover Please keep this user guide in a safe place For Australian CustomersAustralia if you need assistance Before you call for service or assistance…Customer Care New Zealand if you need assistanceDealer Suburb Town Country Product detailsPage Page NZ AU PAC SG