Fisher & Paykel NZ AU PAC SG Inlet hoses, Levelling your machine, Cold supply only

Page 5

Installation instructions

 

3

 

Inlet hoses

Note: new hose sets provided with the machine are to be used to connect the washer to the water mains. Old hose sets should not be re-used.

1Connect the straight ends of the inlet hoses to the taps (there are washers fitted in both ends). Connect the red connector hose to hot, and the white connector hose to cold (if your hoses are colour-coded).

2 Connect the elbow ends of the inlet hoses to the corresponding machine

Tap end Machine end

inlet valves.

 

Fig.3 Inlet hose ends

Inlet valves are marked on the back of the machine.

H = Hot   

C = Cold

 

Minimum height of taps to clear the top of the machine is 1150 mm.

Cold supply only:

If you only have a cold water supply, an inlet valve cap (blanking cap) MUST be connected to the hot inlet valve. The cap prevents water leaking out of the hot valve. The cap is available from your Fisher & Paykel Dealer or Authorised Repairer, Part No. 388491P. This appliance incorporates backflow protection complying with AS3500.1. No further backflow protection is required for connection to the water supply.

Note: your washer does not have an internal heater to heat water.

Inlet hose replacement

We recommend replacing the inlet hoses every 5 years. Hoses should be checked from time to time and replaced if any wear, cuts, bulges, kinks or leaks are found.

1

2

Levelling your machine

It is IMPORTANT to level the machine to ensure even spin performance.

If not already installed, fit the rubber inserts into all 4 feet on the base of the machine.

Move the machine to its final position (we suggest a minimum clearance of 20 mm each side).

Corner cabinets

Adjustable feet Rubber insert

Fig.4 Adjusting the levelling feet

3

Adjust all four feet (wind down) so the machine is level and does not rock.

To check if your machine is level:

Look down on the wash bowl and make sure it sits slightly forward of centre (see Diagram 1). Close the lid. Visually check that the lid fits evenly on both sides. If it does not look like the diagram in the middle, adjust one of the feet slightly until it matches. The diagram on the top and bottom are not correct (see Diagram 2).

Diagram 1

Correct

Incorrect

To check levelling look down on the wash bowl

Lid alignment Lid

Diagram 2

Wind left foot down (out) to correct

Topdeck Lid

Topdeck Lid

Wind right foot down (out) to correct

Topdeck

Fig.5 To assess levelling, check lid alignment

4Turn on the water and check all hose connections for leaks. Check for leaks again after 24 hours. Make sure there are no kinks in the hoses.

5Uncoil the power cord, remove and discard the plastic pin cover, and plug into the wall socket.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents
Installation instructions Intelligence working for you Contents Unpacking Installation instructionsLocation Drain hoseInlet hoses Inlet hose replacementLevelling your machine Cold supply onlyAccessories and spare parts Clothes washer safetyWater supply DrainingBefore you do your first wash Getting startedFabric softener Using your WashSmart washerDetergent Wash cycles If you wish to stop your WashSmart washerWash options AdvanceWA65T60M MW613, MW60, WA55T56M MW513, WA75T56M MWC12 Using your QuickSmart washerIf you wish to stop your QuickSmart washer PowerLID Locked light Lid lockBasic cycle descriptions Default settingsModel variations Wash options and advancing the cycle Clothes care safeguardsTo select the wash options Wash progress lightsAuto water level Water levelsManual water level selection Quick wash Wash options saving water and timeWash options Delay StartSoak Nappy sanitisers/bleachWashing woollens Washing bulky itemsFavourite cycle Favourite cycleTo set your favourite cycle To use your favourite cycleTo customise a cycle Customising the wash cyclesSorting Before you washLoading Lint givers Lint collectorsChoosing the right detergent DetergentHow much detergent? Adding the detergentFabric softener Cleaning the dispenserHow the fabric softener is dispensed How much fabric softener?Changing pre-set options Option adjustment modeTo enter option adjustment mode Use the buttons on the panel to change the pre-set options Rinse options Wash temperaturesEnd of cycle beeps Controlled coldAuto water fill level Light on OptionSpecifications Out of balance recovery routineCleaning your washer Caring for your washer When you have finishedCleaning the inside of your washer Machine informationAutomatic lint system Washer sounds and beepsWater saving tips Saving waterRecycling the wash water Recycling the water from a deep rinseReturn Hose to Drain Manual suds save with syphon backCold water temperature light is flashing HOT water temperature light is flashingHOT and Cold water temperature lights are flashing High water level light is flashingIf your washer beeps for help Single beep every second and... possible solutionsLID Locked light is flashing Some lights are on but the pattern of lights is unfamiliarOperating problems Wash problems Tangling Dye transferThese warranties do not cover Manufacturer’s WarrantyFisher & Paykel undertakes to Please keep this user guide in a safe place For Australian CustomersCustomer Care Before you call for service or assistance…New Zealand if you need assistance Australia if you need assistanceDealer Suburb Town Country Product detailsPage Page NZ AU PAC SG
Related manuals
Manual 44 pages 49.75 Kb