To transport the washer:
1.Shut off both water faucets.
2.Disconnect and drain water inlet hoses.
3.If the washer will be moved during freezing weather, put 1 qt (1 L) of
4.Disconnect the drain from the drain system.
5.Unplug the power cord.
6.Place the inlet hoses into the basket.
7.Drape the power cord and drain hose over edge into the basket.
8.Place foam packing ring from the original shipping materials in the top of washer. If you do not have the original foam packing ring, place heavy blankets, towels, etc. into basket opening. Close the lid and put a piece of tape over the lid and down to the front of the washer. Keep lid taped until the washer is placed into the new location.
Reinstalling the washer
1.Follow the "Installation Instructions" to locate, level and connect the washer.
2.Run the washer through the Bulky/Bedding cycle to clean the washer and remove the antifreeze, if used. Use only High Efficiency (HE) detergent. Use 1/2the manufacturer's recommended amount for a
TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of a service call...
Did you add too much detergent?
Washer displaying code messagesAlways measure detergent. Follow detergent manufacturer's directions.
•L_c "LF" (Washer is taking too long to fill) Check the following:
Are the water inlet hoses kinked or clogged? Are the water inlet valve screens clear?
Is the drain hose installed properly? See "Connect the Drain Hose."
Press STOP to clear display.
J
• L_ "Ld" (Washer is taking too long to drain water from
the wash tub)
Check the following:
Is the drain hose kinked or clogged?
Is the drain hose installed properly? See "Connect the Drain Hose." Press STOP to clear display.
• UL "uL" (Unbalanced Load)
If the load is unbalanced, the washer will display this code while running an imbalanced load correction routine at the end of the wash cycle and before the final spin. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, open lid and redistribute the load. Close lid and press START.
• _3L "oL" (Over Load)
Is the washer overloaded? The washer has attempted to fill and begin the wash cycle. If the washer is overloaded, it will drain any water and detergent that was added during the fill. To correct the overload, remove several items and add detergent. Close lid and press START.
• _d "Sd" (Suds Detected)
Did you use regular detergent?
Regular or
If excessive suds are detected, the washer will display this code while running a suds reduction correction routine at the end of the wash cycle. The suds reduction routine removes extra suds and assures proper rinsing of your garments. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped,
•I r_ "lid" (Lid Opened)
Is the lid open? Close the lid to clear the display. If the lid remains open for more than 10 minutes, water in the wash tub will drain.
•H_ "HC" (Cold and Hot hoses switched)
This code will appear at the end of the wash cycle to indicate that the cold and hot water inlet hoses are switched. See
"Connect the Inlet Hoses."
•_[ "dL" (Door/Lid cannot lock)
Indicates lid is not locked. Check for items caught in the lid keeping it from closing. Press STOP once to clear the code.
•_U "dU" (Door/Lid cannot unlock)
Is there excessive weight on the lid, such as a basket of
laundry? Excessive weight will keep the lid from unlocking. Press STOP once to clear the code.
•F__ "F##" code
Press STOP once to clear code. Press START. If code appears again, call for service.
Noisy, vibrating,
•Is the washer level? Does the washer rock when pushed against the corners?
The washer must be level. The front and rear feet must be in firm contact with the floor. Check that the Iocknuts are tightened. See "Level the Washer."
21