Alternate Parts

Parts listed are available from your local Sears store or Sears Service Center. For further information, call 1-800-4-MY-HOME e (1-800-469-4663).

If You Have:			You Will Need to Buy:
Laundry tub or			Sump pump		system			(if not already
standpipe		taller	available)
than 96" (2.4 m)
1" (2.5 cm)			2" (5 cm)	diameter			to	1" (2.5 cm)
diameter		standpipe	diameter	standpipe			adapter,
			Part Number 3363920 and connector kit
			Part Number 285835
Overhead		sewer	Standard	20 gal. (76 L) 39" (99 cm) tall
			drain tub or utility sink, sump pump and
			connectors		(available			from local
			plumbing	suppliers)
Floor	drain		Siphon break, Part Number 285834;
			additional	drain		hose,
			Part Number 8318155 and connector kit,
			Part Number 285835
Water	faucets		2 longer	water		fill hoses:
beyond reach of fill			6 ft (1.8 m) Part Number						76314,
hoses			10 ft (3.0 m) Part Number						350008
Lint clogged drain			Drain protector,			Part		Number 367031

Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk."

Your washer can be installed in a basement, laundry room, closet, or recessed area. See "Drain System."

IMPORTANT: Do not install or store the washer where it will be exposed to the weather.

Proper installation is your responsibility.

You will need"

•A water heater set to deliver 120°F (49°C) water to the washer.

•A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. See "Electrical Requirements."

•Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water fill valves, and water pressure of 20-100 psi (138-690 kPa) for best performance.

•A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on carpeting is not recommended.

•A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).

Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer Care" for information on winterizing.

Installation spacing for recessed area and closet installations

The following spacing dimensions are recommended for this washer. This washer has been tested for installation with spacing of 0" (0 cm) clearance on the sides. Recommended spacing should be considered for the following reasons:

•Additional spacing should be considered for ease of installation and servicing.

Additional spacing should be considered on all sides of the washer to reduce noise transfer.

For closet installation with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Companion appliance spacing should also be considered.

_! 3"*

(7.6crn)

_ 3"*

(7.6cm)

-T

A. Front view

B. Side view

C. Closet door with vents

*Required spacing

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See "Tools and Parts."

Standpipe drain system--wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe adapter kit is available. See "Tools and Parts."

The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm) from the bottom of the washer.

39"

(99 cm)

Alternate Parts

If You Have:

You Will Need to Buy:

Standpipe drain system--wall or floor (views A & B)