Electrolux 12700 VI manual Positioning, Levelling, Set the machine

Page 51

Installation

Set the machine

upright and remove the two remaining bolts

from the back.

Pull out the three

plastic spacers from the holes into which the bolts were fitted.

Plug the open holes with the plugs which you will find in the plastic bag containing the instruction booklet.

You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is not impeded by carpets, rugs etc.

•Before placing it on small tiles, apply a rubber coating.

•Never try to correct any unevenness in the floor by putting pieces of wood, cardboard or similar materials under the machine.

•If it is impossible to avoid positioning the machine next to a gas cooker or coal-burning stove, an insulating panel (85x57 cm) covered with aluminium foil on the side facing the cooker or stove, must be inserted between the two appliances;

•The machine must not be installed in rooms where the temperature can drop below 0°C.

•The water inlet hose and the drain hose must not be kinked.

•Please ensure that when the appliance is installed, it is easily accessi- ble for the engineer in the event of a breakdown.

Levelling

Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor.

51

Image 51

Contents Lavamat 12700 VI Turbo Dear customer Contents Programme charts Building-in Technical data Service & Spare Parts Guarantee ConditionsSafety instructions General safetyInstallation During use Child safetyDisposal Packaging materialsMachine Tips for environmental protection Main features of your washer-dryer Front view Description of the applianceControl panel Programme selector dialSelector is divided into 5 sections START/PAUSE button Delay Start buttonON/OFF button Mains-on lightProgramme Option buttons Drying Time buttonThis function cannot be used with Quick and Prewash PrewashProgramme progress display DisplayOpening the door after the programme has started Cancelling/Altering a programmeBefore the first wash Detergent dispenser drawerSorting out and preparing the laundry Preparing the wash cycleSynthetics Easy-cares Weight of laundryTypes of fabric and care labels CottonDelicates Which detergent? Detergents and additivesTraditional Powders Which form?As a dryer, the machine works on the condensation principle Preparing the drying cycleLoad Garments not suitable for dryingFibre residue Drying symbols on garment labelsDuration of the drying cycle Modification of the drying timeAdditional drying Add detergent and additive How to washSwitching the machine on Load the laundrySelection of the desired wash programme Selection of the Spin Speed or Rinse Hold optionSelection of the Extra Rinse option Selection of the Delay Start option If the delay start option has been selected, the machineStarting the programme How to dry At the end of the programmeDrying only NON-STOP programme Automatic washing and dryingWash programmes Programme chartTo empty press Special programmesDrying Exterior Cleaning and maintenancePeriodical cleaning After each washDoor seal Drain filterWater inlet filter Emergency emptying out Frost precautionsSomething not working? TroubleshootingProblem Noisy Feet have not been E10 White residue is left on the laundry Unsatisfactory washing resultsIf grey stains remain on the laundry Foam is still visible even after the last rinseTechnical data Water pressure 50 800 kPaThis appliance complies with the following EC directives Help us to help you Service & Spare PartsService & Spare Parts 08705 929Customer care Guarantee Conditions Italy Pordenone +39 1678 Sweden Stockholm +46 738 Slough +44 European GuaranteeSafety instructions for the installer Instructions for installation and electrical connectionRear view Front view and side viewTic bag and the previously removed screw InstallationUnpacking Carefully slide out the right poly- thene bagPositioning LevellingSet the machine Do not connect to a hot water supply Water inlet cold water connection onlyWater drainage Connect the hose to a tap with a 3/4 threadElectrical connections Interest of the environmentPermanent connection Green and Yellow Earth BlueBrown Live Hinges Preparation and assembly of the doorBuilding-in DoorCounter-magnet Mounting the doorSee Fig. H Drill four fixing holes see Fig. GBuilding-in