Electrolux 12700 VI manual Water inlet cold water connection only, Water drainage

Page 52

Installation

Water inlet (cold water connection only)

Connect the hose to a tap with a 3/4” thread.

Installation should comply with local water authority and building regulations’ requirements.

Set the hose correctly

by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks.

Do not connect to a hot water supply.

The inlet hose is provided with a water stop device, which protects against damage caused by water leaks in the hose which could develop due to natural ageing of the hose. This fault is shown by a red sector in the window “A”. Should this occur, turn the water tap off and refer to your Service Force Centre to replace A the hose.

Water drainage

The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic “U-Piece” supplied. The standpipe should have an internal diameter of approximately 38 mm (see dia- gram) thus ensuring there is an air break between the drain hose and standpipe.

When discharging into a stand- pipe ensure that the top of the curve in the hose end is no more than 90 cm (35.4”) and no less than 60 cm (23.6”) above floor level.

3 pin

Max. 90 cm.(35.4")

Min.60 cm.(23.6")

The upright standpipe should have a minimum length of 30 cm (12”) from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water.

Min. 30 cm.(12")

38mm.(1/2") diameter standpipe

52

Image 52

Contents Lavamat 12700 VI Turbo Dear customer Contents Programme charts Technical data Service & Spare Parts Guarantee Conditions Building-inGeneral safety Safety instructionsInstallation Child safety During usePackaging materials DisposalMachine Tips for environmental protection Main features of your washer-dryer Description of the appliance Front viewProgramme selector dial Control panelSelector is divided into 5 sections Delay Start button ON/OFF buttonMains-on light START/PAUSE buttonDrying Time button Programme Option buttonsPrewash This function cannot be used with Quick and PrewashDisplay Programme progress displayCancelling/Altering a programme Opening the door after the programme has startedDetergent dispenser drawer Before the first washPreparing the wash cycle Sorting out and preparing the laundryWeight of laundry Types of fabric and care labelsCotton Synthetics Easy-caresDelicates Detergents and additives Which detergent?Which form? Traditional PowdersPreparing the drying cycle LoadGarments not suitable for drying As a dryer, the machine works on the condensation principleDrying symbols on garment labels Duration of the drying cycleModification of the drying time Fibre residueAdditional drying How to wash Switching the machine onLoad the laundry Add detergent and additiveSelection of the Spin Speed or Rinse Hold option Selection of the desired wash programmeSelection of the Extra Rinse option If the delay start option has been selected, the machine Selection of the Delay Start optionStarting the programme At the end of the programme How to dryDrying only Automatic washing and drying NON-STOP programmeProgramme chart Wash programmesSpecial programmes To empty pressDrying Cleaning and maintenance Periodical cleaningAfter each wash ExteriorDrain filter Door sealWater inlet filter Frost precautions Emergency emptying outTroubleshooting Something not working?Problem Noisy Feet have not been E10 Unsatisfactory washing results If grey stains remain on the laundryFoam is still visible even after the last rinse White residue is left on the laundryWater pressure 50 800 kPa Technical dataThis appliance complies with the following EC directives Service & Spare Parts Service & Spare Parts08705 929 Help us to help youCustomer care Guarantee Conditions European Guarantee Italy Pordenone +39 1678 Sweden Stockholm +46 738 Slough +44Instructions for installation and electrical connection Safety instructions for the installerFront view and side view Rear viewInstallation UnpackingCarefully slide out the right poly- thene bag Tic bag and the previously removed screwLevelling PositioningSet the machine Water inlet cold water connection only Water drainageConnect the hose to a tap with a 3/4 thread Do not connect to a hot water supplyInterest of the environment Electrical connectionsGreen and Yellow Earth Blue Permanent connectionBrown Live Preparation and assembly of the door Building-inDoor HingesMounting the door Counter-magnetDrill four fixing holes see Fig. G See Fig. HBuilding-in