Component Testing Information
!WARNING
To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing requires power.
| Illustration |
| Component | Test Procedure | Results |
|
|
| Thermistor | Unplug harness connector and test |
|
|
|
|
| from wire insertion side. |
|
|
|
|
| Pin #6 and Pin #3 of CN3 | 13000 ohms @ 70F (2.5V DC) |
|
|
| Door Switch | Unplug harness connector and test |
|
|
|
|
| from wire insertion side. |
|
|
|
|
| Pin #7 of CN5 and Pin #3 of CN9 | 60 ohms |
|
|
|
| Pin #8 of CN5 and Pin #3 of CN9 | 60 ohms |
|
|
|
|
|
|
|
|
| Water Sensor | Check voltage at Pin #6 and Pin #7 of |
|
|
|
|
| CN3. | Reset water level = 2.5V DC, 25.8 KHz |
|
|
|
| Check voltage at Pin #6 and Pin #8 of |
|
|
|
|
| CN3. | Reset water level = 2.5V DC, 25.8 KHz |
|
|
|
|
|
|
|
|
| Sump Sensor | Check voltage at Pin #4 and Pin #2 of |
|
|
|
|
| CN8. | 0V DC or 3.75V |
|
|
|
| Check voltage at Pin #4 and Pin #3 of |
|
|
|
|
| CN8. | 0V DC or 3.75V |
|
|
| Motor | Unplug harness connector and test |
|
|
|
|
| from wire insertion side. |
|
|
|
|
| Pin #1 and Pin #2 of CN9 | 11.6 ohms |
|
|
|
| Pin #1 and Pin #3 of CN9 | 11.6 ohms |
|
|
|
| Pin #2 and Pin #3 of CN9 | 11.6 ohms |
|
|
|
|
|
|
|
|
| Drain Pump | During drain check voltage at Pin #1 of |
|
|
|
|
| CN5 and Pin #6 of CN10 | 120V AC |
|
|
|
|
|
|
|
|
| Water Valves | Unplug harness connector and test |
|
|
|
|
| from wire insertion side. |
|
|
|
|
| (Hot valve) Pin #2 of CN5 and Pin #2 |
|
|
|
|
| of CN6 | 1100 ohms |
|
|
|
| (Pre valve) Pin #3 of CN5 and Pin #2 |
|
|
|
|
| of CN6 | 1100 ohms |
|
|
|
| (Bleach valve) Pin #4 of CN5 and Pin |
|
|
|
|
| #2 of CN6 | 1100 ohms |
|
|
|
| (Main valve) Pin #1 of CN5 and Pin #2 |
|
|
|
|
| of CN6 | 1100 ohms |
|
|
|
|
|
|
|
|
| Heater Relay | During water heat check voltage at Pin |
|
|
|
|
| #1 of CN5 and Pin #2 of RY9 | 120V AC |
|
|
| AC Power | Check voltage at Pin #1 and Pin #3 of |
|
|
|
|
| CN5 | 120V AC |
|
|
|
| Check voltage at Pin #1 of CN5 and |
|
|
|
|
| Pin #1 of CN6 | 120V AC |
|
|
| Reactor | Unplug harness connector and test |
|
|
|
|
| from wire insertion side. | Less than 1 ohm |
©2005 Maytag Services |
| 16025909 Rev. 0 | 21 | ||