American Dryer Corp MDG-50 installation manual

Page 34

NOTES: 1. If the anti-wrinkle program is active, the L.E.D. (light emitting diode) display will continue to read "donE", and the microprocessor controller (computer) will proceed through the anti-wrinkle program until the maximum "Active Guard Time" has expired or until the door is opened, whichever comes first. The L.E.D. (light emitting diode) display will read "FILL" or "Amount to Start."

2.If the anti-wrinkle program is not active or in use, the L.E.D. (light emitting diode) display will read "FILL" or "Amount to Start."

2.Timed Mode (Microprocessor [Computer] Models)

a.When turning on power or when no cycle is in progress, the L.E.D. (light emitting diode) display will read "FILL" or "Amount to Start."

b.Insert Coins.

Once the correct "Amount to Start" has been inserted the L.E.D. (light emitting diode) display will read "PUSH."

c.Select temperature by pushing "HI TEMP," "LO TEMP," or "PERM PRESS." The dryer will start, and the L.E.D. (light emitting diode) display will read the temperature cycle selected and the drying time.

d.The dryer will continue through the drying and cooling cycles, showing time counting downward.

IMPORTANT: If the door is opened during a cycle, both the heat and motor will stop. However, the microprocessor controller (computer) will continue to count down in time. Continuation of the cycle will resume only after the door has been closed and any other of the three (3) temperature selection buttons is again depressed.

e.Upon completion of drying and cooling cycles, the tone (buzzer) will sound for five (5) seconds, and the L.E.D. (light emitting diode) display will read "donE", at which time the dryer will shut off.

NOTES: 1. If the anti-wrinkle program is active, the L.E.D. (light emitting diode) display will continue to read "donE", and the microprocessor controller (computer) will proceed through the anti-wrinkle program until the maximum "Active Guard Time" has expired or until the door is opened, whichever comes first. The L.E.D. (light emitting diode) display will read "FILL" or "Amount to Start."

2.If the anti-wrinkle program is not active or in use, the L.E.D. (light emitting diode) display will read "FILL" or "Amount to Start."

3.Free Dry Mode (Microprocessor [Computer] Models)

a.When turning on power or when no cycle is in progress, the L.E.D. (light emitting diode) display will read "FILL" or "FrEE."

30

Page 33 Page 35
Image 34
Page 33 Page 35
Contents MDG-50 Installation Manual Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Section Routine Maintenance Section Important InformationSafety Precautions Personal Injury or Fire could ResultPage Specifications SpecificationsSpecifications Installation Procedures Unpacking and Setting UPLocation Requirements Dryer Enclosure Requirements Fresh AIR Supply Exhaust Requirements Single Dryer Venting Illus. B Multiple Dryer Common Venting ILLUS. D Importantventingreminders Electrical Information Electrical RequirementsMust be Provided Odfn Klwh Uhhq Important a Circuit Serving Each Dryer Must be Provided DG-50 GAS GAS Information Injury and Improper Operation of the DryerType of GAS Page Page Preparation for Operation and START-UP Preoperational Tests Preoperational Instructions Page OPL Models Shut Down Instructions Service PartsReturning Warranty Cards SectionRoutine Maintenance CleaningAdjustments LubricationNo L.E.D. light emitting diode display TroubleshootingDrive motor not operating does not start Blower motor not operating does not start Microprocessor computer display reads dSFL Microprocessor controller computer display reads doorNo heat, ignitor sparks, burner goes on and off right away Dryer operates but is taking too long to dry Condensation on main door glass Dryer or scraping noise at basket tumbler areaMain burners are burning with a yellow flame Excessive noise or vibrationDrive motor only not operating Blower motor only not operating Heating unit not operating ALL temperature selectionsDryer operates but is taking too long to dry load Dryer is cycling on hi-limit thermostat Technical Information Data LabelSerial Number Reversing Timer SPIN/DWELL Adjustments Timing LegendProcedure for Functional Check Replacement Components Direct Spark Ignition DSI System 10/30/00-150
Top Page Image Contents