Panasonic PAN4570 manual Embertm Insight Adaptor Configuration

Page 11

CLASSIFICATION

 

 

No.

 

 

REV.

Einstufung

 

 

DS-Eval4570-2400

 

C

SUBJECT

EvalBoard PAN4570

PAGE

 

 

 

Thema

 

 

Seite

11 of 20

 

CUSTOMER’S CODE

 

PANASONIC’S CODE

DATE

06.11.2006

EvalPAN4570

 

 

Datum

8.4. EMBERTM INSIGHT ADAPTOR CONFIGURATION

The EmberTM Insight Adaptor is used for programming and debugging of PAN4570 application software. As delivered the Adaptor is configured to support DHCP, in case your site is configured for static IP addresses the Adaptor has to be configured for static IP address as well.

In order to to configure the Insight Adaptor for static IP address do the following steps: Connect a USB cable from your pc to the InSight adapter’s USB connector.

On the pc run a standard terminal emulation program to connect to the InSight adapter (the InSight adapter appears as a COM port).

Remark: Using the USB connection as a serial communication connection might

require a driver for USB<->serial.This driver can be aquired from FTDI: http://www.ftdichip.com/Drivers/VCP.htm

Configure your terminal emulator with the settings :

115200 (baud)

8 (data bits) n (no parity)

1 (stop bit)

Flow Control = None

Issue the following InSight adapter commands through the terminal emulator:

ip_static <ipaddress> <netmask> <gateway> ip_dhcp off

For more details see also [5]

Important: Press the red RESET button on the front of the InSight Adaptor or reset the Adaptor by unplugging/plugging the dc supply plug.

9.EMBER ZIGBEE IMPLEMENTATION

9.1FLASH PROGRAMMING OF PAN4570

The following steps describe the use of the EmberTM Insight Adaptor as programmer.

1.Check the latest documentation on the Ember™ tools (see also part 9.1.)

2.Install the EmberZNet™ (currently Version 2.5.0) package on your PC Install EmberTM xIDE.

3.Check if DHCP should be ON or OFF according to 8.4.

4.Important:

Because the Ember™ Insight Adaptor provides power to PAN4570, remove the PAN4570 carrierboard from the ISM transceiver testboard before connecting it to the Ember™ Insight Adaptor. Set the power slide switch on the Ember™ Insight Adaptor to the appropriate (right) position. Power up the Ember™ Insight Adaptor .

European Technology Center

Panasonic Electronic Devices (EUROPE) GmbH

APPROVED

genehmigt

CHECKED

geprüft

DESIGNED

Erstellt

Image 11
Contents Manual Evaluation-Board for PAN4570 Wireless Module Table of Contents Software Needed Contents of the Evaluation KITOverview Hardware NeededSetting UP the Evalboard Testboard Layout Input buttons Output LEDs PAN4570 SMA socketJP3 Power Supply D.C. Power from a Power SupplyOperation of the Testboard JP2Power on D.C. Power from a USB DeviceSerial Port ResetBegin upload CCCCCC… Upload of Emberznet Sample ApplicationsLED Gpio Selecting the Hardware PlatformEmber Zigbee Implementation Flash Programming of PAN4570 Embertm Insight Adaptor ConfigurationFor details on using the em2xxload.exe utility see also Classification REV GPIO4 GPIO5 Reset Rstb Sifclk Sifmiso Sifmosi SifloadbDevelopment of Applications VbatChannel Testing for IEEE802.15.4 ParametersSheet Schematic of the ISM RF Transceiver TestboardSheet PAN4570 Carrierboard History for this Document Related DocumentsDocument Status Life Support Policy General Information