Motorola GR300 service manual Carrier Only Repeat Open Repeater

Page 31

Section 6

Programming

The ZR310 will reference the system ID user for the proper TPL/DPL encode and the Morse ID to send. You can use a disabled or enabled user number.

The Morse code station ID is sent after a 0.75 second key up delay.

Carrier Only Repeat (Open Repeater)

You can program the ZR310 to repeat based on just the carrier, sometimes called "carrier controlled repeat", or "open repeater". In this mode, the ZR310 provides simultaneous tone/open repeater operation for users that have TPL or DPL encode or that have no encode repeat. Both types of users operate normally. This allows a mix of TPL tone users with open repeat capability and is ideal when adding tone users to an existing open repeater.

To enable the carrier (CSQ) for repeat, you can identify a user number as the "carrier repeat user". This allows all standard user- programmable features for open repeat, including enable/disable, TPL or DPL code encoding, etc for the carrier user, if the CSQ user number is set to "0", no carrier repeat will be available.

Accessory PTT TPL/DPL encode

An accessory device such as a tone remote or local microphone may key the transmit radio, and take over control of the repeater. The accessory may need the ZR310 to encode a particular TPL tone or DPL code in order to communicate with a specific user group. The ZR310 incudes a programmable " Accessory PTT encode" settings to accomplish this function. When an accessory keys the transmit radio, the ZR310 will disable the repeater transmit hold time until 30 seconds of no accessory transmit has expired.

Anti-Kerchunker Timer

The anti-kerchunker timer may be programmed between 0 (off) and 5.0 seconds.

The first transmission from a user must be longer than the anti-kerchunker timer value or the programmed transmit hold time will not be used. This discourages users from "kerchunking" the repeater.

Timeout Timer

The timeout timer is a "stuck mic" timeout feature. Its setting determines the maximum amount of time a mobile may transmit on the channel. Each time the TPL/DPL decode stops, the timer is reset. It may be set from 1 to 9 minutes, in one minute increments, and the default setting is 3 minutes. During a timeout condition, you will hear an alert tone before the transmit radio unkeys.

March, 1993

6880902Z68-O

Section 6-9

Image 31
Contents Radius GR300 Table Of Contents ZR310 Community Repeater Panel Theory of Operation Table Of Contents ZR310 Community Repeater Panel Appendix a Dtmf Commands Overview Standard FeaturesSystem Configuration Section IntroductionPhysical Description User FunctionsSection Introduction Assembly Section InstallationEquipment Required For Installation Installation ProceduresZR310, Rear View Fan Installation Section Installation Section 6880902Z68-O March Part Number Description Qty GR300 Housing Kit HLN8391March 6880902Z68-O Section Section Operation Reserved Users When a User Unkeys RadioRegenerated TPL/DPL/CSQ Carrier RepeatAccessory PTT Encode Reserve ModeBarge In Privacy Mode Stuck Mic Timeout TimerRepeater Set-up/Knockdown Section Theory of Operation Squelch/Repeater Audio TPL EncodingDPL Encoding Beep Tone EncodingSection Maintenance Top Cover Removal TroubleshootingSection Programming Programming Via Radio Service Software RSSGetting Started Programming the Repeater Get/Save, Repeater ModeReading the Transmitter Radio Read Receiver Screen March 6880902Z68-O Section Reading the ReceiverConfiguring the System Command Key Function Morse ID interval, Speed, and Frequency System Programmable FieldsCarrier Only Repeat Open Repeater User Programmable Fields Enable a UserRadio Parameters View All UsersCustomizing Your Accessories Low Battery AlertProgramming Over-The-Air Entering the Program ModeEntering a Command Exiting the Program ModeSystem Commands Program Mode Access CodeMic Dtmf Hang Time Station ID Interval Carrier Repeat CSQ UserSystem ID User Station ID FrequencyStation ID Speed Table A-1. Dtmf System Commands Function Parmeter Appendix a Dtmf CommandsTable A-2. Dtmf Diagnostic Commands Function Parameter