SUPER MICRO Computer H8DMT user manual Installing the OS/SATA Driver, Building a Driver Diskette

Page 38

H8DMT/H8DMT-IBX/H8DMT-F/H8DMT-IBXF User’s Manual

Installing the OS/SATA Driver

Before installing the OS (operating system) and SATA RAID driver, you must decide if you wish to have the operating system installed as part of a bootable RAID array or installed to a separate non-RAID hard drive. If on a separate drive, you may install the driver either during or after the OS installation. If you wish to have the OS on a SATA RAID array, you must follow the procedure below and install the driver during the OS installation.

Building a Driver Diskette

You must first build a driver diskette from the Supermicro CD-ROM that was included with the system. (You will have to create this disk on a computer that is already running and with the OS installed.)

1.Insert the CD into your CD-ROM drive and start the system. A display as shown in Figure 2-10will appear.

2.Click on the icon labeled BUILD DRIVER DISKETTES AND MANUALS and follow the instructions to create a floppy disk with the driver on it.

3.Once it's been created, remove the floppy and insert the installation CD for the Windows Operating System you wish to install into the CD-ROM drive of the new system you are about to configure.

Enabling SATA RAID in the BIOS

Before installing the Windows Operating System, you must change some settings in the BIOS. Boot up the system and hit the <DEL> key to enter the BIOS Setup Utility. After the Setup Utility loads, do the following:

1.Use the arrow keys to move to the EXIT menu. Scroll down with the arrow keys to the LOAD OPTIMAL DEFAULTS setting and press <ENTER>. Select OK to confirm, then <ENTER> to load the default settings.

2.Use the arrow keys to move to the ADVANCED menu, then scroll down to NVIDIA RAID SETUP and press the <ENTER> key.

3.Once in the submenu, scroll down to NVIDIA RAID FUNCTION and enable the setting, which will cause the SATA0/1/2 PRIMARY/SECONDARY settings to appear. Enable the SATA devices and channels you will be using.

4.Hit the <ESC> key twice and scroll to the EXIT menu. Select SAVE CHANGES AND EXIT, then hit <ENTER>, then hit <ENTER> again to verify.

5.After exiting the BIOS Setup Utility, the system will reboot. When prompted during the startup, press the <F10> key when prompted to run the nVidia RAID Utility program.

2-18

Image 38
Contents H8DMT/H8DMT-F H8DMT-IBX/H8DMT-IBXF H8DMT/H8DMT-IBX/H8DMT-F/H8DMT-IBXF User’s Manual Manual Organization PrefaceAbout this Manual H8DMT/H8DMT-IBX/H8DMT-F/H8DMT-IBXF User’s Manual Table of Contents I/O Port and Control Panel Connections Appendix B Bios Post Checkpoint Codes Viii Overview ChecklistChapter Introduction Images and Layouts H8DMT/H8DMT-IBX Family Serverboard ImageH8DMT-F/H8DMT-IBXF Family Serverboard Image H8DMT-IBX/H8DMT-IBXF Family Serverboard Layout Jumpers ConnectorsQuick Reference LEDsServerboard Features CPUNVidia MCP55 Pro Chipset System Block Diagram Chipset OverviewPC Health Monitoring Power Configuration Settings Power Supply Super I/OContacting Supermicro HeadquartersReturning Merchandise for Service Installation Procedure Chapter InstallationPrecautions Static-Sensitive DevicesProcessor and Heatsink Installation Removing the CPU Cover PlatePlacing the CPU into the Socket Mounting the Mainboard into a Chassis Secure the CPU with Socket LeverInstalling Memory Side and Top Views of DDR InstallationMaximum Memory I/O Port and Control Panel ConnectionsSupport Front Control Panel Connector DefinitionsPower Connector Reset Connector Auxiliary Power ConnectorPwon Connector Overheat/Fan Fail LED OHPower On LED NIC2 LAN2 LEDUSB Headers NMI ButtonUniversal Serial Bus Ports LAN1/2 Ethernet Ports Serial PortsFan Headers Dedicated LAN Ethernet PortWake-On-LAN Overheat LEDChassis Intrusion SMBus HeaderExplanation of Jumpers Jumper SettingsPower I2C LAN Controller Enable/Disable Cmos ClearI2C to PCI-Express Slot BMC/Video Enable/DisableWatch Dog Enable/Disable Power LED Onboard IndicatorsInfiniBand Port Enable/Disable InfiniBand LED IndicatorsSata Ports Drive ConnectionsEnabling Sata RAID Installing the OS/SATA Driver Building a Driver DisketteInstalling Drivers Installing the OS and Drivers10. Driver/Tool Installation Display Screen Before Power On Chapter TroubleshootingTroubleshooting Procedures No PowerLosing the System’s Setup Configuration Technical Support ProceduresMemory Errors Frequently Asked Questions Returning Merchandise for Service Introduction Starting the Setup UtilityChapter Main MenuSystem Time/System Date Advanced Settings MenuBios Features Submenu Sata Configuration Submenu Last StatePCI/PnP Configuration Submenu MWDMA0. MDWDMA1, MWDMA2, UDMA0. UDMA1, UDMA2, UDMA3NorthBridge Configuration Submenu Advanced Chipset Control SubmenuSouthBridge/MCP55 Configuration Submenu Processor & Clock Options Submenu10. Console Redirection Submenu I/O Device Configuration SubmenuDMI Event Logging Submenu 12. Ipmi Configuration 11. Hardware Health Monitor SubmenuSecurity Menu Boot Menu13. Boot Menu 14. Security MenuExit Menu 15. Exit MenuAppendix a Bios Error Beep Codes Table A-1. Amibios Error Beep CodesH8DMT/H8DMT-IBX/H8DMT-F/H8DMT-IBXF User’s Manual Uncompressed Initialization Codes Appendix B Bios Post Checkpoint CodesBootblock Recovery Codes Chipset Last page for additional information Above 1 MB next 82h A3h Disclaimer H8DMT/H8DMT-IBX/H8DMT-F/H8DMT-IBXF User’s Manual