Multiquip jwn24hscsl, jwn24htcsl operation manual Sound Power Level in dBA

Page 14

specifications/dimensions

Table 2. Noise and Vibration Emissions for Model JWN24HTCSL

Guaranteed ISO 11201:2010 Based

92

Sound Pressure Level at Operator Station in dB(A)

 

Guaranteed ISO 3744:2010 Based

112

Sound Power Level in dB(A)

 

Whole Body Vibration Per ISO 2631-1:1997 +A1:2010

0.15

in m/s2 A(8)

 

NOTES:

1.Sound Pressure and Power Levels are “A” weighted Measures per ISO 226:2003 (ANSI S1.4-1981). They are measured with the operating condition of the machine which generates the most repeatable but highest values of the sound levels. Under normal circumstances, the sound level will vary depending on the condition of the material being worked upon.

2.The vibration level indicated is the vector sum of the RMS (Root Mean Square) Values of amplitudes on each axis, standardized to an 8 hour exposure period, and obtained using operating condition of the machine that generates the most repeatable but highest values in accordance with the applicable standards for the machine.

3.Per EU Directive 2002/44/EC, the daily exposure action value for whole body vibration is 0.5 m/s2 A(8). The daily exposure limit value is 1.15 m/s2 A(8).

Table 3. Engine Specifications/Dimensions

 

Model

Honda GX690RTAF Engine

 

 

Type

4 Stroke, Overhead Valve, 90 degree

 

 

V-Twin 2 cylinder gasoline engine.

 

 

 

 

 

Piston Displacement

40.9 cu.in. (670 cc)

 

 

Max. Output

22.1 bhp/3,600 rpm (16.5 KW)

 

 

Max. Torque

35.6 lbf-ft at 2,500 rpm

 

 

Cooling System

Forced Air

 

 

Engine Oil Capacity

1.6 qt. (1.50 liters)

 

 

1.8 qt. (1.7 liters w/oil filter replacement)

 

 

 

 

 

 

Unleaded gasoline

 

 

Fuel

Octane rating of 86 or higher.

 

 

Maximum 10% ethanol.

 

 

 

 

 

 

See engine manual for further details.

 

 

Fuel Consumption

1.71 gph

 

 

Starting System

Electric Start/CDI Type Magneto Ignition

 

 

Spark Plug Type

ZFR5F NGK

 

 

Spark Plug Gap

0.028-0.031 in. (0.70 - 0.80 mm)

 

 

Length

16.9 in. (42.9 cm)

 

 

Height

17.2 in. (43.8 cm)

 

 

Width

17.7 in. (45.0 cm)

 

 

Weight (dry)

99.9 lbs (45.3 kg)

 

 

 

 

 

page 14 — JWN-SERIES RIDE-ON POWER TROWEL • operation manual — rev. #1 (05/12/12)

Image 14
Contents MODELs Jwn24htcsl Jwn24hscsl Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningTable of Contents Specifications are subject to change without noticeTraining Checklist CompletelyDaily pre-operation checklist Daily pre-Operation ChecklistSafety Information SaFeTy meSSageSGeNeRaL SaFeTy „ NeveR tamper with the factory settings TROWeL SaFeTyENgINe SaFeTy Order Form PT-160TRaNSpORTINg SaFeTy FueL SaFeTyBaTTeRy SaFeTy „ Use well-insulated gloves when picking up the batteryTOWINg SaFeTy „ aLWayS shutdown engine before transportingEmission Control Label ENvIRONmeNTaL SaFeTyEmISSIONS INFORmaTION Label must remain with the engine for its entire lifeSpecifications/dimensions Trowel SpecificationsSound Power Level in dBA Whole Body Vibration Per ISO 2631-11997 +A12010 M/s 2 ∑A8General information Components Components FrontComponents Rear Fuel Filter Filters fuel for contaminants Basic engineMuffler Used to reduce noise and emissions Battery Setup Control Handle AssemblySeat Assembly Set-upGearbox Oil Level InspectionEngine Oil Level FuelStarting the Engine OperationImportant Information Before You Start Forward Direction Maintenance Fuel Filter 200 Hours Changing Engine Oil 100 HoursOil Filter 200 Hours Oil And Fuel LinesChecking The Drive Belt Belt Guard RemovalSPARE Drive Belt Removal Using Replacement Drive Belt Spare Belt RemovalPlace spare drive belt onto clutch as shown in Figure Starting The Trowel/TestingReinstall belt guard assembly Engine’s exhaust contains harmful emissionsCV-joint Assembly installation left-side How it worksTwin PitchTM Blade PitchSingle Pitch „„Do the pitch control towers rock back and forth? Blade Pitch Adjustment ProcedureChanging Blades Clean-Up Trowel Arm Adjustment ProcedureRemove the trowel arm from the spider plate Trowel Arm RemovalTrowel Blade Removal Trowel Arm Adjustment Checking Trowel Arm StraightnessReassembly Trowel Arm Adjustment Fixture ComponentsLifting/Crush Hazard. do not lift trowel with pans attached Installing Pans Onto Finisher BladesDecommissioning Trowel/Components Wiring diagram BlockCombination Switch Continuity Wiring diagram component locator REF. Connector Function DESTroubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Troubleshooting Ride-On mechanical Trowel Wiring? Page HERE’S HOW to GET Help