Multiquip jwn24hscsl Changing Engine Oil 100 Hours, Oil Filter 200 Hours, Fuel Filter 200 Hours

Page 24

maintenance

9.Reinstall the foam air filter element in the air cleaner cover, then reinstall the paper air filter element and cover to the air cleaner case. Securely latch the four hook tabs on the air cleaner cover.

CAUTION

Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating.

Changing Engine Oil (100 Hours)

1.Change the engine oil after the first 20 hours of use, then change every 6 months or 100 hours.

2.Remove the oil filler cap (Figure 5, Item 1), and fill engine crankcase with recommended type oil as listed in Figure 6. Fill to the upper limit of dipstick.

3.Crankcase oil capacity is 1.6 qts. (1.50 liters) without oil filter replacement, with oil filter replacement 1.8 qts. (1.7 liters).

Oil Filter (200 Hours)

1. Replace the engine oil filter (Figure 14) every 200 hours.

OIL

FILTER

SEAL

Figure 14. Oil Filter

2.Be sure to coat the seal of the new oil filter with clean engine oil.

Fuel Filter (200 Hours)

1. Replace the engine fuel filter (Figure 15) every 200 hours.

Figure 15. Honda Fuel Filter

Oil And Fuel Lines

„„Check the oil and fuel lines and connections regularly for leaks or damage. Repair or replace as necessary.

„„Replace the oil and fuel lines every two years to maintain the line's performance and flexibility.

Engine Tune-Up

„„See your engine manual for specific information on tuning up your engine, checking and gaping the spark plugs, etc.

NOTICE

See the engine manual supplied with your machine for appropriate engine maintenance schedule and troubleshooting guide for problems.

Long Term Storage

„„Remove the battery.

„„Drain fuel from fuel tank, fuel line and carburetor.

„„Remove spark plug and pour a few drops of motor oil into cylinder. Crank engine 3 to 4 times so that oil reaches all internal parts.

„„Clean exterior with a cloth soaked in clean oil.

„„Store unit covered with plastic sheet in moisture and dust-free location out of direct sunlight.

CAUTION

NEVER store the ride-on trowel with fuel in the tank for any extended period of time. Always clean up spilled fuel immediately.

page 24 — JWN-SERIES RIDE-ON POWER TROWEL • operation manual — rev. #1 (05/12/12)

Image 24
Contents MODELs Jwn24htcsl Jwn24hscsl Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningTable of Contents Specifications are subject to change without noticeTraining Checklist CompletelyDaily pre-operation checklist Daily pre-Operation ChecklistSafety Information SaFeTy meSSageSGeNeRaL SaFeTy TROWeL SaFeTy ENgINe SaFeTy„ NeveR tamper with the factory settings Order Form PT-160FueL SaFeTy BaTTeRy SaFeTyTRaNSpORTINg SaFeTy „ Use well-insulated gloves when picking up the batteryTOWINg SaFeTy „ aLWayS shutdown engine before transportingENvIRONmeNTaL SaFeTy EmISSIONS INFORmaTIONEmission Control Label Label must remain with the engine for its entire lifeSpecifications/dimensions Trowel SpecificationsSound Power Level in dBA Whole Body Vibration Per ISO 2631-11997 +A12010 M/s 2 ∑A8General information Components Components FrontComponents Rear Basic engine Muffler Used to reduce noise and emissionsFuel Filter Filters fuel for contaminants Control Handle Assembly Seat AssemblyBattery Setup Set-upInspection Engine Oil LevelGearbox Oil Level FuelOperation Important Information Before You StartStarting the Engine Forward Direction Maintenance Changing Engine Oil 100 Hours Oil Filter 200 HoursFuel Filter 200 Hours Oil And Fuel LinesChecking The Drive Belt Belt Guard RemovalSPARE Drive Belt Removal Using Replacement Drive Belt Spare Belt RemovalStarting The Trowel/Testing Reinstall belt guard assemblyPlace spare drive belt onto clutch as shown in Figure Engine’s exhaust contains harmful emissionsCV-joint Assembly installation left-side How it worksBlade Pitch Single PitchTwin PitchTM Blade Pitch Adjustment Procedure Changing Blades„„Do the pitch control towers rock back and forth? Clean-Up Trowel Arm Adjustment ProcedureTrowel Arm Removal Trowel Blade RemovalRemove the trowel arm from the spider plate Trowel Arm Adjustment Checking Trowel Arm StraightnessReassembly Trowel Arm Adjustment Fixture ComponentsInstalling Pans Onto Finisher Blades Decommissioning Trowel/ComponentsLifting/Crush Hazard. do not lift trowel with pans attached Wiring diagram BlockCombination Switch Continuity Wiring diagram component locator REF. Connector Function DESTroubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Troubleshooting Ride-On mechanical Trowel Wiring? Page HERE’S HOW to GET Help