Multiquip jwn24htcsl, jwn24hscsl operation manual Troubleshooting engine

Page 39

 

troubleshooting

 

 

 

 

 

 

 

Troubleshooting (engine)

 

Symptom

possible problem

Solution

 

 

 

 

Spark plug bridging?

Check gap, insulation or replace spark plug.

 

 

 

 

Carbon deposit on spark plug?

Clean or replace spark plug.

 

 

 

 

Short circuit due to defi cient spark plug

Check spark plug insulation, replace if worn.

 

insulation?

 

 

 

Improper spark plug gap?

Set to proper gap.

 

Fuel reaching carburetor?

Check fuel line.

 

Water in fuel tank?

Flush or replace fuel tank.

 

Fuel fi lter clogged?

Replace fuel fi lter.

Diffi cult to start, fuel is available, but no spark

Stuck carburetor?

Check fl oat mechanism.

Spark plug is red?

Check transistor ignition unit.

at spark plug.

 

 

If insuffi cient compression, repair or replace

 

Spark plug is bluish white?

engine. If injected air leaking, correct leak. If

 

 

carburetor jets clogged, clean carburetor.

 

 

 

 

 

Check transistor ignition unit is broken, and

 

No spark present at tip of spark plug?

replace defective unit. Check if voltage cord

 

cracked or broken and replace. Check if

 

 

 

 

spark plug if fouled and replace.

 

 

 

 

No oil?

Add oil as required.

 

 

 

 

Oil pressure alarm lamp blinks upon starting?

Check automatic shutdown circuit, "oil

 

(if applicable)

sensor". (if applicable)

 

ON/OFF switch is shorted?

Check switch wiring, replace switch.

Diffi cult to start, fuel is available, and spark is

Ignition coil defective?

Replace ignition coil.

Improper spark gap, points dirty?

Set correct spark gap and clean points.

present at the spark plug.

Condenser insulation worn or short circuiting?

Replace condenser.

 

 

Spark plug wire broken or short circuiting?

Replace defective spark plug wiring.

 

Wrong fuel type?

Flush fuel system, and replace with correct

 

type of fuel.

 

 

Diffi cult to start, fuel is available, spark is

 

 

Water or dust in fuel system?

Flush fuel system.

present and compression is normal.

 

 

Air cleaner dirty?

Clean or replace air cleaner.

 

 

 

 

 

Choke open?

Close choke.

 

 

 

 

Suction/exhaust valve stuck or protruded?

Reseat valves.

 

 

 

Diffi cult to start, fuel is available, spark is

Piston ring and/or cylinder worn?

Replace piston rings and/or piston.

 

 

Cylinder head and/or spark plug not tightened

 

present and compression is low.

Torque cylinder head bolts and spark plug.

 

properly?

 

 

Head gasket and/or spark plug gasket damaged?

Replace head and spark plug gaskets.

 

 

 

 

No fuel in fuel tank?

Fill with correct type of fuel.

 

 

 

 

Fuel cock does not open properly?

Apply lubricant to loosen fuel cock lever,

 

replace if necessary.

No fuel present at carburetor.

 

 

 

Fuel fi lter/lines clogged?

Replace fuel fi lter.

 

 

 

 

 

Fuel tank cap breather hole clogged?

Clean or replace fuel tank cap.

 

 

 

 

Air in fuel line?

Bleed fuel line.

 

 

 

JWN-SERIES RIDE-ON POWER TROWEL • operation manual — rev. #1 (05/12/12) — page 39

Image 39
Contents MODELs Jwn24htcsl Jwn24hscsl Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsSpecifications are subject to change without notice Table of ContentsCompletely Training ChecklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGeNeRaL SaFeTy Order Form PT-160 TROWeL SaFeTyENgINe SaFeTy „ NeveR tamper with the factory settings„ Use well-insulated gloves when picking up the battery FueL SaFeTyBaTTeRy SaFeTy TRaNSpORTINg SaFeTy„ aLWayS shutdown engine before transporting TOWINg SaFeTyLabel must remain with the engine for its entire life ENvIRONmeNTaL SaFeTyEmISSIONS INFORmaTION Emission Control LabelTrowel Specifications Specifications/dimensionsWhole Body Vibration Per ISO 2631-11997 +A12010 M/s 2 ∑A8 Sound Power Level in dBAGeneral information Components Front ComponentsComponents Rear Basic engine Muffler Used to reduce noise and emissionsFuel Filter Filters fuel for contaminants Set-up Control Handle AssemblySeat Assembly Battery SetupFuel InspectionEngine Oil Level Gearbox Oil LevelOperation Important Information Before You StartStarting the Engine Forward Direction Maintenance Oil And Fuel Lines Changing Engine Oil 100 HoursOil Filter 200 Hours Fuel Filter 200 HoursBelt Guard Removal Checking The Drive BeltSpare Belt Removal SPARE Drive Belt Removal Using Replacement Drive BeltEngine’s exhaust contains harmful emissions Starting The Trowel/TestingReinstall belt guard assembly Place spare drive belt onto clutch as shown in FigureHow it works CV-joint Assembly installation left-sideBlade Pitch Single PitchTwin PitchTM Blade Pitch Adjustment Procedure Changing Blades„„Do the pitch control towers rock back and forth? Trowel Arm Adjustment Procedure Clean-UpTrowel Arm Removal Trowel Blade RemovalRemove the trowel arm from the spider plate Checking Trowel Arm Straightness Trowel Arm AdjustmentTrowel Arm Adjustment Fixture Components ReassemblyInstalling Pans Onto Finisher Blades Decommissioning Trowel/ComponentsLifting/Crush Hazard. do not lift trowel with pans attached Block Wiring diagramCombination Switch Continuity REF. Connector Function DES Wiring diagram component locatorTroubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Troubleshooting Ride-On mechanical Trowel Wiring? Page HERE’S HOW to GET Help