Multiquip jwn24htcsl, jwn24hscsl operation manual Components Rear

Page 17

components

17.Rear Light — The JWN-Series Ride-On Power Trowel has three 12 volt halogen lights.

18.Lift Loops — Located on both sides of the main frame. Used to lift the trowel.

19.Retardant SprayTank — Holds 5 gallons of retardant.

20.Retardant Spray Pump — Delivers retardant to the spray nozzle.

21.EZ-Mover Boss — Rear attachment point for EZ Mover. Used to transport the trowel.

22.Right-Side Spider — Consists of trowel arms, blades, wear plate, and thrust collar.

23.Left-Side Spider — Consists of trowel arms, blades, wear plate, and thrust collar.

24.Document Box — Contains all product documentation.

25.Battery — Provides +12V DC power to the electrical system.

26.Belt Guard — Encloses drive belt used in conjunction with clutch.

27.Charcoal Canister — Charcoal activated system that absorbs or traps fuel vapors. Basic component of evaporative emissions control systems

28.Safety Kill Switch — Shuts down engine when seat is not occupied by operator.

28

17

		18	18
		18	24
	25	26	24
	25		27

25

RETARDANT ONLY

20

22	21	19	21	23
	Figure 3. Components – Rear

JWN-SERIES RIDE-ON POWER TROWEL • operation manual — rev. #1 (05/12/12) — page 17

Image 17

Contents MODELs Jwn24htcsl Jwn24hscsl Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsSpecifications are subject to change without notice Table of ContentsCompletely Training ChecklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGeNeRaL SaFeTy ENgINe SaFeTy TROWeL SaFeTy„ NeveR tamper with the factory settings Order Form PT-160BaTTeRy SaFeTy FueL SaFeTyTRaNSpORTINg SaFeTy „ Use well-insulated gloves when picking up the battery„ aLWayS shutdown engine before transporting TOWINg SaFeTyEmISSIONS INFORmaTION ENvIRONmeNTaL SaFeTyEmission Control Label Label must remain with the engine for its entire lifeTrowel Specifications Specifications/dimensionsWhole Body Vibration Per ISO 2631-11997 +A12010 M/s 2 ∑A8 Sound Power Level in dBAGeneral information Components Front ComponentsComponents Rear Fuel Filter Filters fuel for contaminants Basic engineMuffler Used to reduce noise and emissions Seat Assembly Control Handle AssemblyBattery Setup Set-upEngine Oil Level InspectionGearbox Oil Level FuelStarting the Engine OperationImportant Information Before You Start Forward Direction Maintenance Oil Filter 200 Hours Changing Engine Oil 100 HoursFuel Filter 200 Hours Oil And Fuel LinesBelt Guard Removal Checking The Drive BeltSpare Belt Removal SPARE Drive Belt Removal Using Replacement Drive BeltReinstall belt guard assembly Starting The Trowel/TestingPlace spare drive belt onto clutch as shown in Figure Engine’s exhaust contains harmful emissionsHow it works CV-joint Assembly installation left-sideTwin PitchTM Blade PitchSingle Pitch „„Do the pitch control towers rock back and forth? Blade Pitch Adjustment ProcedureChanging Blades Trowel Arm Adjustment Procedure Clean-UpRemove the trowel arm from the spider plate Trowel Arm RemovalTrowel Blade Removal Checking Trowel Arm Straightness Trowel Arm AdjustmentTrowel Arm Adjustment Fixture Components ReassemblyLifting/Crush Hazard. do not lift trowel with pans attached Installing Pans Onto Finisher BladesDecommissioning Trowel/Components Block Wiring diagramCombination Switch Continuity REF. Connector Function DES Wiring diagram component locatorTroubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Troubleshooting Ride-On mechanical Trowel Wiring? Page HERE’S HOW to GET Help