Multiquip jwn24htcsl, jwn24hscsl Starting The Trowel/Testing, Reinstall belt guard assembly

Page 27

maintenance

6.Place spare drive belt onto clutch as shown in Figure 20

CLUTCH

GROOVES

DRIVE

BELT

Figure 20. Spare Drive Belt Placement (Clutch)

7.Reinstall belt guard assembly.

Starting The Trowel/Testing

1.While sitting in the operator’s position, start the trowel as referenced in the Operator’s Manual. Be sure to check the engine oil level prior to starting the engine.

CAUTION

The engine’s exhaust contains harmful emissions.

ALWAYS have adequate ventilation when operating. Direct exhaust away from nearby personnel.

2.Run machine, bringing throttle up so clutch engages. Cycle the engine from idle to full throttle twice, and shut off engine. Remove key.

Spare Drive belt installation CV-joint Assembly Removal (left-side)

1.If necessary, place the trowel on suitable supports (jack-stands) and observe all safety precautions.

2.Starting at the left-side gearbox, use a 1/4" allen wrench and remove the 3 bolts and lock washers that secure the CV-joint (Figure 21) to the left-side gearbox. Retain mounting hardware for later use.

REMOVE 3 PLACES

GAP

LEFT-SIDE

GEARBOX CV-JOINT COUPLER

Figure 21. CV-Joint Removal

3.Once the CV-joint has been separated from the left- side gearbox coupler, push the CV-joint inward so that a gap (Figure 21) exists between the gearbox coupler and CV-joint.

4.Slide new spare drive belt between gearbox coupler and CV-joint.

	SPARE DRIVE	INSTALL
	BELT HOLDER
		2 PLACES
	(INSTALL)

LEFT-SIDE

GEARBOX

ADAPTER PLATE

COUPLER

CV-JOINT

SPARE

DRIVE BELT

Figure 22. Spare Drive Belt Routing

5.Mount new spare drive belt and cover ( Figure 22) onto left-side gearbox. Reinstall the 2 bolts that secure the spare belt holder to the left-side gearbox adapter plate.

JWN-SERIES RIDE-ON POWER TROWEL • operation manual — rev. #1 (05/12/12) — page 27

Image 27

Contents MODELs Jwn24htcsl Jwn24hscsl Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsSpecifications are subject to change without notice Table of ContentsCompletely Training ChecklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGeNeRaL SaFeTy Order Form PT-160 TROWeL SaFeTyENgINe SaFeTy „ NeveR tamper with the factory settings„ Use well-insulated gloves when picking up the battery FueL SaFeTyBaTTeRy SaFeTy TRaNSpORTINg SaFeTy„ aLWayS shutdown engine before transporting TOWINg SaFeTyLabel must remain with the engine for its entire life ENvIRONmeNTaL SaFeTyEmISSIONS INFORmaTION Emission Control LabelTrowel Specifications Specifications/dimensionsWhole Body Vibration Per ISO 2631-11997 +A12010 M/s 2 ∑A8 Sound Power Level in dBAGeneral information Components Front ComponentsComponents Rear Basic engine Muffler Used to reduce noise and emissionsFuel Filter Filters fuel for contaminants Set-up Control Handle AssemblySeat Assembly Battery SetupFuel InspectionEngine Oil Level Gearbox Oil LevelOperation Important Information Before You StartStarting the Engine Forward Direction Maintenance Oil And Fuel Lines Changing Engine Oil 100 HoursOil Filter 200 Hours Fuel Filter 200 HoursBelt Guard Removal Checking The Drive BeltSpare Belt Removal SPARE Drive Belt Removal Using Replacement Drive BeltEngine’s exhaust contains harmful emissions Starting The Trowel/TestingReinstall belt guard assembly Place spare drive belt onto clutch as shown in FigureHow it works CV-joint Assembly installation left-sideBlade Pitch Single PitchTwin PitchTM Blade Pitch Adjustment Procedure Changing Blades„„Do the pitch control towers rock back and forth? Trowel Arm Adjustment Procedure Clean-UpTrowel Arm Removal Trowel Blade RemovalRemove the trowel arm from the spider plate Checking Trowel Arm Straightness Trowel Arm AdjustmentTrowel Arm Adjustment Fixture Components ReassemblyInstalling Pans Onto Finisher Blades Decommissioning Trowel/ComponentsLifting/Crush Hazard. do not lift trowel with pans attached Block Wiring diagramCombination Switch Continuity REF. Connector Function DES Wiring diagram component locatorTroubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Troubleshooting Ride-On mechanical Trowel Wiring? Page HERE’S HOW to GET Help