Multiquip jwn24htcsl Installing Pans Onto Finisher Blades, Decommissioning Trowel/Components

Page 35

maintenance

Installing Pans Onto Finisher Blades

These round discs sometimes referred to as “pans” attach to the spiders arms and allow early floating on wet concrete and easy movement from wet to dry areas. They are also very effective in embedding large aggregates and surface hardeners.

WARNING

Lifting/Crush Hazard. DO NOT lift trowel with pans attached.

WARNING

ALWAYS install pans either on the work area or on an area that is next to and level with the work area. DO NOT lift the trowel when the pans are attached.

Refer to Figure 36 when installing pans onto finisher blades.

Knob,Tie-Down

Z-Clip Pans

Tie-Down,

Blade

 

Blade

Z-Clip Pan

Assembly

Figure 36. Z-Clip Finisher Pan Instructions

1.Lift trowel just enough to slide pan under blades. Lower finisher onto pan with blades adjacent to Z-Clips.

2.Rotate blades into position under Z-Clips. Ensure that the blades are rotated in the direction of travel when the machine is in operation or use the engine to rotate the blades into position.

3.Attach the blade tie-downs to the far side of the Z-Clip brackets with tie-down knobs as shown in Figure 36.

4.Check to make certain that the blade edges are secured under the Z-Clips and the tie-downs are secured completely over the edges of the blade bar before the machine is put back into operation.

Decommissioning Trowel/Components

Decommissioning is a controlled process used to safely retire a piece of equipment that is no longer serviceable. If the equipment poses an unacceptable and unrepairable safety risk due to wear or damage or is no longer cost effective to maintain, (beyond life-cycle reliability) and is to be decommissioned, (demolition and dismantlement), the following procedure must take place:

1.Drain all fluids completely. These may include oil, gasoline, hydraulic oil and antifreeze. Dispose of properly in accordance with local and governmental regulations. Never pour on ground or dump down drains or sewers.

2.Remove battery and bring to appropriate facility for lead reclamation. Use safety precautions when handling batteries that contain sulfuric acid, (Reference Setup Section).

3.The remainder can be brought to a salvage yard or metal reclamation facility for further dismantling.

JWN-SERIES RIDE-ON POWER TROWEL • operation manual — rev. #1 (05/12/12) — page 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents MODELs Jwn24htcsl Jwn24hscsl Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsSpecifications are subject to change without notice Table of ContentsCompletely Training ChecklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGeNeRaL SaFeTy Order Form PT-160 TROWeL SaFeTyENgINe SaFeTy „ NeveR tamper with the factory settings„ Use well-insulated gloves when picking up the battery FueL SaFeTyBaTTeRy SaFeTy TRaNSpORTINg SaFeTy„ aLWayS shutdown engine before transporting TOWINg SaFeTyLabel must remain with the engine for its entire life ENvIRONmeNTaL SaFeTyEmISSIONS INFORmaTION Emission Control LabelTrowel Specifications Specifications/dimensionsWhole Body Vibration Per ISO 2631-11997 +A12010 M/s 2 ∑A8 Sound Power Level in dBAGeneral information Components Front ComponentsComponents Rear Fuel Filter Filters fuel for contaminants Basic engineMuffler Used to reduce noise and emissions Set-up Control Handle AssemblySeat Assembly Battery SetupFuel InspectionEngine Oil Level Gearbox Oil LevelStarting the Engine OperationImportant Information Before You Start Forward Direction Maintenance Oil And Fuel Lines Changing Engine Oil 100 HoursOil Filter 200 Hours Fuel Filter 200 HoursBelt Guard Removal Checking The Drive BeltSpare Belt Removal SPARE Drive Belt Removal Using Replacement Drive BeltEngine’s exhaust contains harmful emissions Starting The Trowel/TestingReinstall belt guard assembly Place spare drive belt onto clutch as shown in FigureHow it works CV-joint Assembly installation left-sideTwin PitchTM Blade PitchSingle Pitch „„Do the pitch control towers rock back and forth? Blade Pitch Adjustment ProcedureChanging Blades Trowel Arm Adjustment Procedure Clean-UpRemove the trowel arm from the spider plate Trowel Arm RemovalTrowel Blade Removal Checking Trowel Arm Straightness Trowel Arm AdjustmentTrowel Arm Adjustment Fixture Components ReassemblyLifting/Crush Hazard. do not lift trowel with pans attached Installing Pans Onto Finisher BladesDecommissioning Trowel/Components Block Wiring diagramCombination Switch Continuity REF. Connector Function DES Wiring diagram component locatorTroubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Troubleshooting Ride-On mechanical Trowel Wiring? Page HERE’S HOW to GET Help
Top Page Image Contents