Multiquip jwn24htcsl, jwn24hscsl operation manual Specifications/dimensions, Trowel Specifications

Page 13

specifications/dimensions

C

A

Figure 1. Dimensions

B

Table 1. Trowel Specifications

A–Length – in. (cm)	77.0 (195.6)
B–Width – in. (cm)	39 (99)
C–Height – in. (cm)1	46.75 (118.7)
Weight – lbs. (kgs.) Operating	685 (311.3)
Weight – lbs. (kgs.) Shipping	885 (402.27)
Engine – H.P.	24 (HONDA)
Fuel Tank – gallons (liters)	5 (19.23)
Rotor – RPM (Dry Concrete)	180 Min
Path Width – in. (cm)	75 (191)
Engine Oil Capacity (w/new filter)	2 Quarts (1.9 Liters)
Gear Box Oil Capacity	69 oz. Mobil SCH 634 Iso VG640

JWN-SERIES RIDE-ON POWER TROWEL • operation manual — rev. #1 (05/12/12) — page 13

Image 13

Contents MODELs Jwn24htcsl Jwn24hscsl Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsSpecifications are subject to change without notice Table of ContentsCompletely Training ChecklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTy meSSageS Safety InformationGeNeRaL SaFeTy ENgINe SaFeTy TROWeL SaFeTy„ NeveR tamper with the factory settings Order Form PT-160BaTTeRy SaFeTy FueL SaFeTyTRaNSpORTINg SaFeTy „ Use well-insulated gloves when picking up the battery„ aLWayS shutdown engine before transporting TOWINg SaFeTyEmISSIONS INFORmaTION ENvIRONmeNTaL SaFeTyEmission Control Label Label must remain with the engine for its entire lifeTrowel Specifications Specifications/dimensionsWhole Body Vibration Per ISO 2631-11997 +A12010 M/s 2 ∑A8 Sound Power Level in dBAGeneral information Components Front ComponentsComponents Rear Muffler Used to reduce noise and emissions Basic engineFuel Filter Filters fuel for contaminants Seat Assembly Control Handle AssemblyBattery Setup Set-upEngine Oil Level InspectionGearbox Oil Level FuelImportant Information Before You Start OperationStarting the Engine Forward Direction Maintenance Oil Filter 200 Hours Changing Engine Oil 100 HoursFuel Filter 200 Hours Oil And Fuel LinesBelt Guard Removal Checking The Drive BeltSpare Belt Removal SPARE Drive Belt Removal Using Replacement Drive BeltReinstall belt guard assembly Starting The Trowel/TestingPlace spare drive belt onto clutch as shown in Figure Engine’s exhaust contains harmful emissionsHow it works CV-joint Assembly installation left-sideSingle Pitch Blade PitchTwin PitchTM Changing Blades Blade Pitch Adjustment Procedure„„Do the pitch control towers rock back and forth? Trowel Arm Adjustment Procedure Clean-UpTrowel Blade Removal Trowel Arm RemovalRemove the trowel arm from the spider plate Checking Trowel Arm Straightness Trowel Arm AdjustmentTrowel Arm Adjustment Fixture Components ReassemblyDecommissioning Trowel/Components Installing Pans Onto Finisher BladesLifting/Crush Hazard. do not lift trowel with pans attached Block Wiring diagramCombination Switch Continuity REF. Connector Function DES Wiring diagram component locatorTroubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Troubleshooting Ride-On mechanical Trowel Wiring? Page HERE’S HOW to GET Help