Cisco Systems 3110G, 3110X, 3012 Gigabit Ethernet Module Slot, Port Numbering, Port Description

Page 10

Chapter 1 Product Overview

Hardware Features

10-Gigabit Ethernet Module Slot

The Catalyst Switch Module 3110X 10-Gigabit Ethernet module slot is used for an uplink connection to other switches and routers. The module slot operates in full-duplex mode and uses the hot-swappable Cisco X2 transceiver modules.

The X2 transceiver modules have a dual SC/PC connector (-SR, -LX4) or an Infiniband 4x connector (-CX4) for connections to multimode fiber (MMF), single-mode fiber (SMF), or 4x Infiniband cable.

These are the supported Cisco X2 transceiver modules:

X2-10GB-SR

X2-10GB-CX4

X2-10GB-LX4

For information about installing a transceiver module, see the “Installing Devices in the 10-Gigabit Ethernet Slot” section on page 2-11. For cable specifications, see Appendix B, “Connector and Cable Specifications.”

Port Numbering

Table 1-2describes the switch module port numbering.

Table 1-2 Switch Module Port Numbering

Port

Description

 

 

Ports 1 to 141

Internal Gigabit Ethernet 1000BASE-X downlink ports that connect to

 

the blade enclosure.

 

 

Ports 15 to 18 (Catalyst Switch

External 10/100/1000BASE-T copper Gigabit Ethernet uplink ports.

Module 3110G and 3012)

 

 

 

Port 1 (X2) (Catalyst Switch

External 10-Gigabit Ethernet module slot.

Module 3110X)

 

 

 

1.The number of internal ports is determined by the blade enclosure model. See the blade enclosure documentation for more information about internal port numbering.

Internal 100BASE-T Ethernet Management Port

The internal Ethernet management port (Fa0) is used only for switch module management traffic, not for data traffic. It is connected to the IBM advanced Management Module (aMM) through the blade enclosure backplane connector. Traffic to and from this port is isolated from the switch module ports. This port only supports autonegotiation with 100 Mb/s and full-duplex mode.

Catalyst Switch Module 3110G, 3110X, and 3012 for IBM BladeCenter Hardware Installation Guide

1-4

OL-12192-01

 

 

Image 10
Contents Americas Headquarters Text Part Number OL-12192-01Page N T E N T S Diagnosing Problems Purpose PrefaceAudience ConventionsRelated Publications Product Overview Switch ModulesSwitch Model IBM Part Number DescriptionHardware Features WS-CBS3012-IBM WS-CBS3012-IBM-ICatalyst Switch Module 10/100/1000 Ethernet PortsInternal 100BASE-T Ethernet Management Port Gigabit Ethernet Module SlotPort Numbering Port DescriptionSwitch Module LEDs Switch Module LEDs and Mode ButtonStack Master LED Mode ButtonSystem Power LED Color System StatusFault LED Fault/Stack Mode LEDStack Member LED Color Activity LED Description Link Status LED Description Port LEDsColor LED Description Console Port Management OptionsStackWise Plus Ports Port Status LED DescriptionNetwork Configurations Preparing for Installation Switch Module InstallationSafety Warnings OL-12192-01 Installation Guidelines Box ContentsInstalling the Switch Module Blade Enclosure Rear-Panel ViewAfter Installing the Switch Module Installing the Switch ModuleCreating Switch Stacks Stacking GuidelinesConnecting a Switch Stack Connecting the StackWise Plus CablesSwitch Stack Cabling Examples 203295 203296 Installing Devices in the 10-Gigabit Ethernet Slot Installing an X2 Transceiver ModuleInstalling an X2 Transceiver Module Removing a ModuleWhere to Go Next Connecting Devices to the Ethernet PortsDevice Crossover Cable OL-12192-01 Verify Switch Module Post Results TroubleshootingDiagnosing Problems Verify Switch Module LEDsEthernet and Fiber Cables Verify Switch Module ConnectionsBad or Damaged Cable Link StatusPing End Device Transceiver IssuesPort and Interface Settings Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Resetting the Switch ModuleVerify Switch Module Performance Autonegotiation and Network Interface CardsHow to Replace a Failed Stack Member Using the Mode Button to Reset the Switch ModuleOL-12192-01 Power Specifications Technical SpecificationsPhysical Specifications Environmental RangesOL-12192-01 Connector Specifications Connector and Cable Specifications10/100/1000 Ports Cable and Adapter Specifications Gigabit Ethernet Module InterfaceGigabit Ethernet X2 Transceiver Module Cable Specifications Four Twisted-Pair Straight-Through Cable Schematic Four Twisted-Pair Cable PinoutsTwo Twisted-Pair Cable Pinouts Identifying a Crossover CableOL-12192-01 Numerics IN-2 IN-3 IN-4