Cisco Systems 3110X, 3110G, 3012 Transceiver Issues, Port and Interface Settings, Ping End Device

Page 33

Chapter 3 Troubleshooting

Diagnosing Problems

Transceiver Issues

Use only Cisco X2 transceiver modules on the switch module. Each Cisco module has an internal serial EEPROM that is encoded with security information. This encoding provides a way for Cisco to identify and validate that the module meets the requirements for the switch module. Evaluate these items:

•Bad or wrong X2 transceiver module. Exchange suspect module with known good module. Verify that the module is supported on this platform. (The switch module release notes on Cisco.com list the X2 modules that the switch module supports.)

•Use the show interfaces privileged EXEC command to verify the port or module error-disabled, disabled, or shutdown status. Re-enable the port if needed.

•Make sure that all fiber connections are properly cleaned and securely connected.

•For CX4 module connections, make sure that cable routing does not violate the minimum allowed cable-bend radius. See the module documentation for specific cabling requirements.

•For LX4 modules, we recommend a mode conditioning patch for MMF applications.

Port and Interface Settings

An obvious but sometimes overlooked cause of port connectivity failure is a disabled port. Verify that the port or interface is not disabled or powered down for some reason. If a port or interface is manually shut down on one side of the link or the other side, the link does not come up until you re-enable the port. Use the show interfaces privileged EXEC command to verify the port or interface error-disabled, disabled, or shutdown status on both sides of the connection. If needed, re-enable the port or the interface.

Ping End Device

Test the end device by pinging from the directly connected switch module first, and then work your way back port by port, interface by interface, trunk by trunk, until you find the source of the connectivity issue. Make sure that each switch module can see the end device MAC address in its Content-Addressable Memory (CAM) table.

Spanning Tree Loops

Spanning Tree Protocol (STP) loops can cause serious performance issues that look like port or interface problems. In this situation, the switch module bandwidth is used over and over again by the same frames, leaving little room for legitimate traffic.

Loops can be caused by a unidirectional link. A unidirectional link occurs whenever the traffic sent by the switch module is received by its neighbor, but the traffic from the neighbor is not received by the switch module. A broken fiber-optic cable, other cabling, or a port issue could cause this one-way communication.

You can enable UniDirectional Link Detection (UDLD) on the switch module to help identify difficult-to-find unidirectional link problems. UDLD supports two modes of operation: normal (the default) and aggressive. In normal mode, UDLD detects unidirectional links due to misconnected interfaces on fiber-optic connections. In aggressive mode, UDLD also detects unidirectional links due to one-way traffic on fiber-optic and twisted-pair links and due to misconnected interfaces on fiber-optic links. For information about enabling UDLD on the switch module, see the “Understanding UDLD” section in the software configuration guide for this release.

Catalyst Switch Module 3110G, 3110X, and 3012 for IBM BladeCenter Hardware Installation Guide

 

OL-12192-01

3-3

 

 

 

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Text Part Number OL-12192-01 Americas HeadquartersPage N T E N T S Diagnosing Problems Audience PrefacePurpose ConventionsRelated Publications Switch Model Switch ModulesProduct Overview IBM Part Number DescriptionWS-CBS3012-IBM WS-CBS3012-IBM-I Hardware Features10/100/1000 Ethernet Ports Catalyst Switch ModulePort Numbering Gigabit Ethernet Module SlotInternal 100BASE-T Ethernet Management Port Port DescriptionSwitch Module LEDs and Mode Button Switch Module LEDsSystem Power LED Mode ButtonStack Master LED Color System StatusFault/Stack Mode LED Fault LEDStack Member LED Port LEDs Color Activity LED Description Link Status LED DescriptionColor LED Description StackWise Plus Ports Management OptionsConsole Port Port Status LED DescriptionNetwork Configurations Switch Module Installation Preparing for InstallationSafety Warnings OL-12192-01 Box Contents Installation GuidelinesBlade Enclosure Rear-Panel View Installing the Switch ModuleInstalling the Switch Module After Installing the Switch ModuleStacking Guidelines Creating Switch StacksConnecting the StackWise Plus Cables Connecting a Switch StackSwitch Stack Cabling Examples 203295 203296 Installing an X2 Transceiver Module Installing Devices in the 10-Gigabit Ethernet SlotRemoving a Module Installing an X2 Transceiver ModuleConnecting Devices to the Ethernet Ports Where to Go NextDevice Crossover Cable OL-12192-01 Diagnosing Problems TroubleshootingVerify Switch Module Post Results Verify Switch Module LEDsBad or Damaged Cable Verify Switch Module ConnectionsEthernet and Fiber Cables Link StatusPort and Interface Settings Transceiver IssuesPing End Device Spanning Tree LoopsVerify Switch Module Performance Resetting the Switch ModuleSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsUsing the Mode Button to Reset the Switch Module How to Replace a Failed Stack MemberOL-12192-01 Physical Specifications Technical SpecificationsPower Specifications Environmental RangesOL-12192-01 Connector and Cable Specifications Connector Specifications10/100/1000 Ports Gigabit Ethernet Module Interface Cable and Adapter SpecificationsGigabit Ethernet X2 Transceiver Module Cable Specifications Four Twisted-Pair Cable Pinouts Four Twisted-Pair Straight-Through Cable SchematicIdentifying a Crossover Cable Two Twisted-Pair Cable PinoutsOL-12192-01 Numerics IN-2 IN-3 IN-4
Top Page Image Contents