Cisco Systems 3012, 3110X, 3110G Connecting a Switch Stack, Connecting the StackWise Plus Cables

Page 23

Chapter 2 Switch Module Installation

Creating Switch Stacks

Connecting a Switch Stack

Follow these steps:

Step 1 Install the member switch modules if you have not already done so.

Step 2 Remove the dust covers from the StackWise Plus cables, and store them for future use.

Step 3 Verify that cables are aligned as shown in Figure 2-3. (The cables are keyed for correct insertion.)

Figure 2-3 Connecting the StackWise Plus Cables

C

O N S O L M EO D E

! M

BM

R S T

LNK 15 ACT

LNK 16 ACT

LNK 17 ACT

LNK 18 ACT

1

STACK

2

 

201898

Step 4 Insert the cable into the StackWise Plus port on the front panel of the switch module. Insert the other end of the cable into the connector of the other switch module.

Always use a Cisco-approved StackWise Plus cable to connect the switch modules.

Caution The new stack-member switch module restarts when you connect the StackWise Plus cables.

Step 5 Configure the member switch modules through the master switch module by using the CLI through the console port of any stack member.

To remove the StackWise Plus cables, grasp the tab on the cable connector, and gently pull straight out. When you remove the StackWise Plus cables, replace the dust covers to protect them from dust.

Caution Removing and installing the StackWise Plus cable can shorten its useful life. Do not remove and insert the cable more often than is absolutely necessary.

Catalyst Switch Module 3110G, 3110X, and 3012 for IBM BladeCenter Hardware Installation Guide

 

OL-12192-01

2-7

 

 

 

Image 23
Contents Text Part Number OL-12192-01 Americas HeadquartersPage N T E N T S Diagnosing Problems Conventions PrefaceAudience PurposeRelated Publications IBM Part Number Description Switch ModulesSwitch Model Product OverviewWS-CBS3012-IBM WS-CBS3012-IBM-I Hardware Features10/100/1000 Ethernet Ports Catalyst Switch ModulePort Description Gigabit Ethernet Module SlotPort Numbering Internal 100BASE-T Ethernet Management PortSwitch Module LEDs and Mode Button Switch Module LEDsColor System Status Mode ButtonSystem Power LED Stack Master LEDStack Member LED Fault/Stack Mode LEDFault LED Color LED Description Port LEDsColor Activity LED Description Link Status LED Description Port Status LED Description Management OptionsStackWise Plus Ports Console PortNetwork Configurations Safety Warnings Switch Module InstallationPreparing for Installation OL-12192-01 Box Contents Installation GuidelinesBlade Enclosure Rear-Panel View Installing the Switch ModuleInstalling the Switch Module After Installing the Switch ModuleStacking Guidelines Creating Switch StacksConnecting the StackWise Plus Cables Connecting a Switch StackSwitch Stack Cabling Examples 203295 203296 Installing an X2 Transceiver Module Installing Devices in the 10-Gigabit Ethernet SlotRemoving a Module Installing an X2 Transceiver ModuleDevice Crossover Cable Connecting Devices to the Ethernet PortsWhere to Go Next OL-12192-01 Verify Switch Module LEDs TroubleshootingDiagnosing Problems Verify Switch Module Post ResultsLink Status Verify Switch Module ConnectionsBad or Damaged Cable Ethernet and Fiber CablesSpanning Tree Loops Transceiver IssuesPort and Interface Settings Ping End DeviceAutonegotiation and Network Interface Cards Resetting the Switch ModuleVerify Switch Module Performance Speed, Duplex, and AutonegotiationUsing the Mode Button to Reset the Switch Module How to Replace a Failed Stack MemberOL-12192-01 Environmental Ranges Technical SpecificationsPhysical Specifications Power SpecificationsOL-12192-01 10/100/1000 Ports Connector and Cable SpecificationsConnector Specifications Gigabit Ethernet Module Interface Cable and Adapter SpecificationsGigabit Ethernet X2 Transceiver Module Cable Specifications Four Twisted-Pair Cable Pinouts Four Twisted-Pair Straight-Through Cable SchematicIdentifying a Crossover Cable Two Twisted-Pair Cable PinoutsOL-12192-01 Numerics IN-2 IN-3 IN-4