Pioneer DJM-5000 operating instructions Operating the PA section

Operating the PA section

Outputting sound from the ZONE terminal

You can output sound from the [ZONE] terminal besides the sound output from the master channel.

1 Set the output channel selector switch for the [ZONE] channel

Select the channel output from the [ZONE] terminal.

!Sound output varies according to the position of the switch.

Switch	1		2		3		4		MASTER	MIC
Position
Audio	CH-1	1	CH-2	1	CH-3	1	CH-4	1	Microphone	Microphone
Output									Channel 2	Channel 3

1Audio is output regardless of the position of faders and control knobs.

2Audio is output regardless of the position of [LEVEL] for the [MASTER] channel.

3Audio is output only from the microphone channel, for which [OUTPUT] is set to [BOTH] or [ZONE].

2 Press [ZONE ON] for the [ZONE] channel

Turn on the [ZONE] channel. The button lights up in green.

3 Rotate [LEVEL] for the [ZONE] channel

Sound is output at the [ZONE] terminal. The zone level indicator lights up.

!To turn the [ZONE] channel off, press [ZONE ON] again. The button turns off.

Using the sound maximizer feature

1 Press [ON/OFF] for [SOUND MAXIMIZER]

Turn on the sound maximizer function. The button lights up in blue.

2 Rotate [CLARITY] or [DYNAMICS]

The effect of the sound maximizer varies according to the rotation direction and position of the control.

!The output audio level increases according to the sound maximizer effect when the dial is turned clockwise. Pay attention to the output audio level when using the sound maximizer function.

dB

	Frequency
DYNAMICS	CLARITY
MIN MAX	MIN MAX

!The range of sound that can be adjusted varies according to the control.

—CLARITY: Adjusts the attack and outline of sound mainly in the mid and high range (high hat, snare, etc.).

—DYNAMICS: Adjusts modulation and rhythm mainly in the low range.

!When you turn off the sound maximizer function, press [ON/OFF] again. The light of the button turns off.

Using the external effector

1 Connect the external effector

[ON/OFF] of [SEND/RETURN] lights up in red. When the external effector is not connected, [ON/OFF] does not light up.

!For details about connections, see Connections on page 7.

2Set the output channel selector switch for the [SEND/RETURN] channel

Select the channel output from the [SEND] terminal.

! Sound output varies according to the position of the switch.

Switch	1	2	3	4	MIC 1	MIC 2	MIC1+2	MASTER
Position
Audio	CH-1	CH-2	CH-3	CH-4	MIC 1	MIC 2	MIC1+2 1	Master Channel
Output

1 The microphone sound output from the master channel is output from the [SEND] chan- nel.

3 Press [ON/OFF] for [SEND/RETURN]

Sound is output at the [SEND] terminal. The button flashes in red.

4 Turn the [LEVEL] dial for [SEND/RETURN]

Adjusts the level of audio signals input at the [RETURN] terminal.

16En

!To stop the sound output at the [SEND] terminal, press the flashing [ON/OFF]. The button lights up.

Switching between monaural and stereo audio

You can switch between monaural and stereo audio for the sound output at the [MASTER1], [MASTER2], [BOOTH], [REC OUT] or [PHONES] terminal.

Switch between [MONO]/[STEREO]

![MONO]: Outputs monaural audio.

![STEREO]: Outputs stereo audio.

Adjusting the L/R balance of audio

The left/right balance of the sound output from the [MASTER1], [MASTER2], [BOOTH], [REC OUT] and [PHONES] terminals can be adjusted.

1Set [MONO]/[STEREO] to [STEREO]

2Rotate [BALANCE]

The L/R balance of audio varies according to the rotation direction and position of the [BALANCE] control.

!Rotating to the rightmost position outputs only the right sound of stereo audio. Rotating to the leftmost position outputs only the left sound of stereo audio.

Audio is output from the [BOOTH] terminal

The master channel audio, except the microphone channel audio, is output from the [BOOTH] terminal regardless of the position of [LEVEL] in the [MASTER] channel.

Rotate [BOOTH MONITOR]

Adjusts the level of audio signals output at the [BOOTH] terminal.