Pioneer DJM-5000 operating instructions Operating the DJ section

Page 14

Operating the DJ section

Outputting sound

1 Press [POWER]

Turn on the power of this unit.

2 Set the input selector switch

Select the input source of each channel from the components connected to this unit.

!To output sound of the computer connected to the [USB] terminal, switch the input selector switch for [CH-2], [CH-3], and [CH-4] to [USB].

3 Rotate [TRIM]

Adjusts the level of audio signals input in each channel.

!The channel level indicator lights when the sound is being properly input to the channel.

4 Set the channel fader to the inner position

Adjusts the level of audio signals output in each channel.

5 Adjust the crossfader assign switch

Switches the output destination of each channel.

[A]: Assigns to [A] (left) of the crossfader.

[B]: Assigns to [B] (right) of the crossfader.

[THRU]: Assigns to the [MASTER] channel (the crossfader is not passed through).

6 Adjust the crossfader curve switch ([CROSS FADER])

Switches the crossfader curve characteristics.

[]: Makes a sharply increasing curve (if the crossfader is moved away from the [A] side, audio signals are immediately output from the [B] side).

[]: Makes a curve shaped between the two curves above and below.

[]: Makes a gradually increasing curve (if the crossfader is moved away from the [A] side, the sound on the [B] side gradually increases, while the sound on the [A] gradually decreases).

7 Set the crossfader

Outputs audio signals assigned by the crossfader assign switch corresponding to the curve characteristics selected by [CROSS FADER] (Crossfader Curve Selector Switch).

!You do not need to follow this step when the crossfader assign switch is set to [THRU].

8 Rotate [LEVEL] for the [MASTER] channel

The sound is output from [MASTER1] and [MASTER2]. The master level indicator lights.

Adjusting the sound quality

Rotate [HI], [MID] or [LOW] in each channel

Refer to Specifications on page 19 for the range of sound that can be adjusted by each control.

Monitoring sound with headphones

1Connect headphones to the [PHONES] jack

2Press [CUE] for the channel to be monitored

The button lights up brightly in orange.

3 Turn the [LEVEL] dial for [HEAD PHONES]

Sound is output from the headphones in the channel selected by [CUE].

!Sound output from the headphones varies according to the combination of channels selected by [CUE]. See the table below.

CH-1

 

 

Headphone Output

 

CH-4

MASTER

ZONE

L channel

R channel

 

 

 

 

 

 

 

 

ON

OFF

OFF

CH (L)

CH (R)

OFF

ON

OFF

MASTER (L)

MASTER (R)

OFF

OFF

ON

ZONE (L)

ZONE (R)

ON

ON

OFF

CH (MONO)

MASTER (MONO)

ON

OFF

ON

CH (MONO)

ZONE (MONO)

OFF

ON

ON

MASTER (L)+ZONE (L)

MASTER (R)+ZONE (R)

ON

ON

ON

CH (MONO)

MASTER (MONO)

+ZONE (MONO)

 

 

 

 

!Monitoring is canceled if you press [CUE] again. The button lights up dimly in orange.

Using the fader to play a Pioneer DJ player (fader start)

If you connect a Pioneer DJ player using a control cable (supplied with a DJ player), you can start playback of control other operations of the DJ player with the fader of this unit.

The fader start feature is available only when a Pioneer DJ player is connected to [CH-1] or [CH-2].

Connect a Pioneer DJ player to this unit in advance (page 8).

Start playback using the channel fader

1Set the crossfader assign switch to [THRU]

2Press [FADER START]

Turn on the fader start function. The button lights up brightly in orange.

3Set the channel fader to the outermost position

4Set the cue on the DJ player

The DJ player pauses playback at the cue point.

5 Set the channel fader to the inner position

Playback starts on the DJ player.

!If you set the channel fader back to the original position, the player instanta- neously returns to the cue point already set and pauses playback (back cue).

Start playback using the crossfader

1Set the crossfader assign switch to [A] or [B]

2Press [FADER START]

Turn on the fader start function. The button lights up brightly in orange.

3 Set the crossfader

Set to the farmost end in the opposite direction to the channel to be fader started.

4 Set the cue on the DJ player

The DJ player pauses playback at the cue point.

5 Set the crossfader

Playback starts on the DJ player.

!If you set the crossfader back to the original position, the player instanta- neously returns to the cue point already set and pauses playback (back cue).

Operating the DJ software

The DJM-5000 also outputs the operating data for the buttons and dials in MIDI format. If you connect a computer with a built-in MIDI-compatible DJ software via a USB cable, you can operate the DJ software on this unit.

Install the DJ software on your computer in advance. Also, adjust audio and MIDI settings for the DJ software.

1 Connect the USB port on this unit to your computer

For details about connections, see Connecting a computer on page 9.

2Start the DJ software

3Set [MIDI] to [ON]

Transmission of the MIDI messages begin.

!You can send MIDI messages altogether according to the position of buttons, faders, or control knobs (snapshot).

!Adjust faders and control knobs to transmit messages based on the corre- sponding position. For details about the messages generated by this unit, see List of MIDI Messages on page 12.

4 Set [MIDI] to [OFF]

The MIDI messages are not transmitted even if you operate this unit.

14En

Image 14
Contents DJM-5000 Information to User Ventilation Caution We Want You Listening For a Lifetime Contents What’s in the box FeaturesBefore start Connections Rear PanelTo an AC outlet Connecting input terminalsConnecting output terminals About the USB audio driver software Connecting to the control panelConnecting a computer Software Use AgreementInstalling the driver software Connecting the DJM-5000 and computerChecking the version of the driver software About USB-MIDI channel settingAdjusting the buffer size Windows Checking the latest information on the driver softwareList of Midi Messages MSBOperations Control PanelOperating the DJ section Using the talk-over feature Using a microphoneUsing the microphone effect feature Operating the MC sectionOperating the PA section About the exemption clauses TroubleshootingAdditional information Block Diagram CUEAudio Section SpecificationsGeneral Input / Output terminalsAvertissement Français Comment lire ce manuel SommaireMontage en rack conforme aux normes Contenu du carton d’emballage Informations préliminairesCaractéristiques Raccordements Panneau arrièreUne prise secteur Raccordement des prises d’entréeRaccordement des prises de sortie Propos du pilote audio USB Raccordement au panneau de commandeRaccordement à un ordinateur Contrat d’utilisation du logicielRaccordement de la DJM-5000 et de l’ordinateur Précautions à prendre lors de l’installationInstallation du pilote Vérification de la version du pilote Propos du réglage du canal USB-MIDIRéglage de la taille de la mémoire tampon Windows Liste de messages Midi Panneau de commande OpérationsRéglage de la qualité du son Fonctionnement de la section DJRestitution du son Contrôle du son par un casqueUtilisation de la fonction effets de microphone Fonctionnement de la section MCUtilisation d’un microphone Utilisation de la fonction talkoverFonctionnement de la section PA Propos des clauses d’exemption Informations supplémentairesEn cas de panne Schéma fonctionnel FrançaisSection audio SpécificationsGénéral Prises d’entrée/sortiePrinted Imprimé au
Related manuals
Manual 54 pages 23.01 Kb