Pioneer DJM-5000 operating instructions Ventilation Caution

Page 3
D3-4-2-1-7b_A_En
D3-4-2-2-4_En
S002*_En
D3-4-2-1-7a_A_En
D3-4-2-1-4_A_En
D3-4-2-2-2a_A_En
D3-4-2-1-3_B_En

FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Product Name: DJ MIXER

Model Number: DJM-5000

Responsible Party Name: PIONEER ELECTRONICS (USA), INC.

SERVICE SUPPORT DIVISION

Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA 90810-1003, U.S.A. Phone: 1-800-421-1404

URL: http://www.pioneerelectronics.com

D8-10-4*_B1_En

English

This Class B digital apparatus complies with Canadian ICES-003.

D8-10-1-3_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230V or 120V) written on the rear panel.

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at rear, and 3 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

D3-4-2-1-7c*_A1_En

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal.

The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-1a_A1_En

CAUTION

The POWER switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

When using this product follow the instructions written on the underside of the unit, which concern rated voltage, etc.

IMPORTANT NOTICE

THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED ON THE BOTTOM.

PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND KEEP IN A SECURE AREA. THIS IS FOR YOUR SECURITY.

D1-4-2-6-1*_A1_En

WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm.

Wash hands after handling

D36-P4_A_En

En 3

Image 3
Contents DJM-5000 Information to User Ventilation Caution We Want You Listening For a Lifetime Contents Features Before startWhat’s in the box Rear Panel ConnectionsConnecting input terminals Connecting output terminalsTo an AC outlet Software Use Agreement Connecting to the control panelConnecting a computer About the USB audio driver softwareConnecting the DJM-5000 and computer Installing the driver softwareChecking the latest information on the driver software About USB-MIDI channel settingAdjusting the buffer size Windows Checking the version of the driver softwareMSB List of Midi MessagesControl Panel OperationsOperating the DJ section Operating the MC section Using a microphoneUsing the microphone effect feature Using the talk-over featureOperating the PA section Troubleshooting Additional informationAbout the exemption clauses CUE Block DiagramInput / Output terminals SpecificationsGeneral Audio SectionAvertissement Français Sommaire Montage en rack conforme aux normesComment lire ce manuel Informations préliminaires CaractéristiquesContenu du carton d’emballage Panneau arrière RaccordementsRaccordement des prises d’entrée Raccordement des prises de sortieUne prise secteur Contrat d’utilisation du logiciel Raccordement au panneau de commandeRaccordement à un ordinateur Propos du pilote audio USBPrécautions à prendre lors de l’installation Installation du piloteRaccordement de la DJM-5000 et de l’ordinateur Propos du réglage du canal USB-MIDI Réglage de la taille de la mémoire tampon WindowsVérification de la version du pilote Liste de messages Midi Opérations Panneau de commandeContrôle du son par un casque Fonctionnement de la section DJRestitution du son Réglage de la qualité du sonUtilisation de la fonction talkover Fonctionnement de la section MCUtilisation d’un microphone Utilisation de la fonction effets de microphoneFonctionnement de la section PA Informations supplémentaires En cas de pannePropos des clauses d’exemption Français Schéma fonctionnelPrises d’entrée/sortie SpécificationsGénéral Section audioPrinted Imprimé au
Related manuals
Manual 54 pages 23.01 Kb