Pioneer VSX-AX10Ai-G manual Programming signals from other remote controls, Pioneer-1 DVR-7000

Page 68

08Controlling other equipment

To exit without saving the preset you have assigned, press CANCEL instead of INSTALL above.

Tip

• Pioneer DVD recorders fall into the following setting

types:

Pioneer-1 – DVR-7000

Pioneer-2–4– DVR-310, DVR-510H

• Use the (cursor up/down) buttons to scroll through the component options (the RECEIVER and TUNER screens are not available).

3On the touch screen, press the button that corresponds to the command you want to teach the remote control.

For example, choose the (play) button to program this remote control to start playback on your DVD player.

If you have more than one Pioneer DVD recorder of

setting type 2–4, you can select different setting types

for each (allowing for separate control).

Programming signals from other remote controls

If the preset code for your component is not available, or the available preset codes do not operate correctly, you can program signals from the remote control of another component. This can also be used to program additional

LEARN END

DVD1/2

DVD

TV

 

CONT

AUDIO

SUBTITLE

DISPLAY

TOP MENU

LEARN END

DVD2/2

DVD

TV

 

CONT

1 2 3 CLR

4 5 6 +10

7 8 9 0

SEARCH RETURN MODE

operations (buttons not covered in the presets) after assigning a preset code in Recalling preset codes on page 66.

1 Press LEARNING on the remote setup menu.

SETUP 1/3

CALIBRATE

PRESET RECALL

LEARNING

MULTI OPERATION

DIRECT FUNCTION

2From the ‘Select Function’ screen, choose the input function which matches the connection for the component you want to control.

For example, press DVD/LD if you want to program signals for the DVD player that you connected to the DVD/LD terminals.

A remote icon shows in the top right corner of the touch screen after you’ve selected a button (you can deselect it by pressing it again).

•Remote control soft keys such as , , (cursor left/right) and TV CONT are used to select menu screens (even in learning mode), so therefore cannot be programmed.

• The Learn and L buttons that appear on some component screens are unassigned buttons which can be used to learn new commands. See Editing remote control button names on page 69 to change the name once you’ve programmed a command.

•You can program the remote control hard keys

(VOLUME +/– and MUTE are only available with TV CONTROL), but the command will remain the same for all screens of the component selected.

•Press END to go back without making any changes.

4While the icon is displayed, point the two remote controls toward each other and press the button on the other remote control corresponding to the operation you want to program.

Select Function

LEARNING

DVD/LD

TV/DVD

SAT

CANCEL

 

3

6

9

 

-

-

 

 

 

 

2

5

8

0

1

4

7

-

-

12 – 30 cm

When the command has been learned, OK! shows on the remote control touch screen and the remote control returns to the command learning screen (step 3). Repeat steps 3 and 4 to program additional commands.

If you want to learn signals for additional components, press END to go back to the Select Function screen and start again from step 2.

68

En

Page 67 Page 69
Image 68
Page 67 Page 69
Contents VSX-AX10Ai-G Operating Environment Risk of Electric Shock Do not OpenVoltage selector Information to UserContents Surround Setup menu Using other functionsAdvanced setup Controlling other equipmentFeatures Our philosophyChecking the supplied accessories Using the remote controlBefore you start Before you start ChapterSetting up the remote control Calibrating the remote control screenBefore you start Press CalibrateSetting the time-out setting Setting the clockSetting the button alert volume Resetting the remote control Locking the remote controlRestarting the remote control Press Reset to DefaultReplacing the lithium-ion batteries Rear panel Connecting your equipmentConnecting your equipment Chapter Connecting your equipment When making cable connectionsConnecting your equipment Connecting your TV Connecting your equipment Connecting a DVD player AssignableConnecting the multichannel analog outputs STB Connecting your equipment Connecting a VCR or DVD recorder VSX-AX10AiConnecting your equipment Connecting other video sources Connecting your equipment Using the component video jacks About the video converterConnecting your equipment Connecting digital audio sources Connecting your equipment Connecting analog audio sources TurntablePortable DVD player, etc Connecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting your equipment Connecting antennas FM wire antennaConnecting external antennas AM loop antennaAbout the supplied AC power cords Plugging in the receiverControls and displays Controls and displays ChapterControls and displays ToneControls and displays Display TunedHome menu screens Controls and displays Remote controlBasic remote control displays Digital NR SetupReceiver menu screens Remote control displays for the tuner Disp ModeSpeaker A/B Display DimmerRemote control displays for other components TV control menu screensOperating menus for additional components Search Mode 10 CLRAutomatically setting up for surround sound Switch on the receiver and your TVGetting started Getting started ChapterGetting started EnterPlaying a source Checking the settings on your DVD or other playerOther problems when using the Auto Surround Setup Change the receiver input to the source you want to play Listening to your system Listening to your system ChapterAbout the listening modes Listening in surround soundListening to your system Dolby Pro Logic IIx Music settingsNeo6 Music settings Using the Advanced surround effects Using the Home THX modesAdjusting the Advanced Surround effect level Use the Option +/- buttons to adjust the effect levelListening with headphones Listening in stereoPro Logic IIx Movie PRO Logic NEO6 CinemaUsing the Stream Direct mode Press Multi CH Input on the remote control Home menu screenSelecting the input signal type AnalogChannel Listening to high-sampling formatsSelecting USB and multichannel analog input channels Listening to your system Using the surround back channel Press SB CH Mode repeatedly to cycle throughAuto Surround back channel optionsVSB Auto VSB on VSB OFF Use the Option +/- buttons to change the settingCreating a center speaker effect Listening to your system Using Hi-bit and Hi-sampling Using Midnight and Loudness listeningUsing the tone control Switching the tone control on or offTreble Adjusting the bass and trebleReducing noise during playback Listening to your system Listening to dual mono soundtracks Using the tuner Using the tuner ChapterFinding a station Changing the frequency stepMPX mode Using the tuner Tuning directly to a stationMemorizing station presets Using the tuner Listening to memorized station presetsNaming station presets AbcdefghijklmnopqrstuvwxyzSurround Setup menu Surround Setup menu ChapterMaking receiver settings from the Surround Setup menu Select ‘Surround Setup’ then press EnterSurround Setup menu Speaker SystemsLarge Channel Level Select ‘Channel Level’ then press EnterSetting the Acoustic Calibration EQ automatically Setting the Acoustic Calibration EQ manuallySpeaker Distance Acoustic Calibration EQCopying your Acoustic Calibration EQ settings Select ‘Manual’ then press EnterSelect CUSTOM1 or CUSTOM2 then press Enter Select ‘Data Copy’ then press EnterProfessional Acoustic Calibration EQ How to use Professional Acoustic Calibration EQHow to interpret the graphical output Using Professional Acoustic Calibration EQ Select a manual setup option and press EnterSelect ‘Professional’ then press Enter If you selected ‘Auto Pro.’, select ‘Start’ and pressSwitch the X-Curve on or OFF CurveUse Cursor left/right buttons to select Select ‘X-Curve’ then press EnterCycle through the settings screen by screen Checking your surround settingsSelect ‘Check’ from the Surround Setup menu and press Enter Using the remote control with other components Recalling preset codesControlling other equipment Controlling other equipment ChapterSelect a setting type Controlling other equipmentPioneer-1 DVR-7000 Programming signals from other remote controlsPress Learning on the remote setup menu Editing remote control button names Press Direct Function on the remote setup menuPress OK to confirm the settings Press KEY Label on the remote setup menuChoose how you want to change the look of the button Press OK when you’ve finishedSelect the button you want to rename LD if the multi operation is being used to switch on From the ‘Select Function’ screen, chooseInput function This will be the one that starts the multi operation whenUsing multi operations Press OK when you’re finishedFrom the remote control Home menu press Multi OperationSwitching components on and off Using the 12 volt triggerUsing System off System OFFUsing other functions Using other functions ChapterMaking an audio or a video recording Monitoring your recordingAdjusting the delay of a soundtrack Use the Option +/- buttons to adjust the amount of delayEnhancing Sacd playback Press Option repeatedly until Sacd Gain shows in the displayUsing other functions Switching the speaker impedanceSwitch the SD1 Normal Stream Direct mode Dimming the displayDefault receiver settings Using other functions Checking your system settingsResetting the system Bypass Using speaker system B Switching the speaker systemUsing speaker system B in another room Other connectionsSelect the ‘ITU-R’ setting from the Speaker Systems menu Other connectionsBi-amping your front speakers SP B ITU-R is selectedConnecting additional amplifiers Bi-wiring your speakersUsing the pre-outs Using the i.LINK interface Connecting an external stereo pre-amplifierCreating an i.LINK network About i.LINKAbout Pqls rate control Using the USB interface Press ‘USB’ on the remote control Home menu ScreenConnecting a PC for Advanced Mcacc output Advanced Mcacc output using your PC Select ‘PC Output’ and press EnterAdvanced setup Advanced setup ChapterMake sure your receiver and TV are both switched on Input Assign menuAssigning the i.LINK inputs Advanced setupAssigning the component video inputs Expert Setup menu Select ‘Expert Setup’ then press EnterAssigning the video inputs Multi in OFF USB OFFOSD Adjustment Bass Peak LevelOSD Overlay Dynamic Range ControlFunction Rename Volt Trigger THX Audio SetupSelect ‘THX Audio Setup’ then press Enter THX Ultra2 Subwoofer Setup Surround Back Speaker PositionOptimizing your speaker setup Basic surround setupAdditional information Additional information ChapterTHX speaker system setup Additional informationNo sound Additional information TroubleshootingPower Listening in surround sound on Symptom Other audio problems Symptom CauseSettings VideoRemote control JackDisplay Select buttonLink interface Link messagesUSB interface MiscellaneousAdditional information Surround sound formats DolbyPCM Pulse Code Modulation About THXWindows Media Audio 9 Professional Maintenance of external surfaces THX Ultra2 Cinema modeAdvanced Speaker Array ASA THX MusicModeAdditional information Specifications 04B00001 ARB7292-A
Top Page Image Contents