Pioneer VSX-AX10Ai-G manual Adjusting the delay of a soundtrack

Page 75

Using other functions

Reducing the level of an analog signal

The input attenuator lowers the input level of an analog signal when it’s too strong. You can use this if you find the that the OVER indicator is lights often, or you can hear distortion in the sound.

•From the remote control receiver menu, press INPUT ATT to switch the input attenuator on or off.

You may need to press RECEIVER on the Home menu () first before reaching the receiver menu screen shown

below (use the (cursor left/right) soft keys to go to the previous/next menu screen).

RECEIVER 3/3

TV

RECEIVER CONT

INPUT	SB CH
INPUT	MODE
SPEAKER	INPUT
A/B	ATT
VIDEO	DISPLAY
SELECT	DIMMER
TAPE2	STATUS
MONITOR	STATUS

09

Adjusting the delay of a soundtrack

Some monitors have a slight delay when showing video, so the soundtrack will be slightly out of sync with the picture. By adding a bit of delay, you can adjust the sound to match the presentation of the video.

1Press OPTION repeatedly until SOUND DELAY shows in the display.

With the remote, you may need to press RECEIVER on the

Home menu () first before reaching the receiver menu

screen shown below (use the (cursor left/right) soft keys to go to the previous/next menu screen).

RECEIVER 2/3

TV

RECEIVER CONT


MIDNIGHT		DIGITAL NR
	TONE	LOUDNESS
–	OPTION		+
–	CH LEVEL		+

ACOUSTIC										TUNER	SBCH
CAL.	MIDNIGHT	LOUDNESS	TONE	OPTION			DIGITALNR	INPUT ATT	CLASS	STATION	MODE
PHONES	SPSYSTEM	SIGNAL	VIDEO	TAPE2	STREAM	SETUP			VIDEOINPUT
PHONES	SPSYSTEM	SIGNAL	VIDEO	TAPE2	STREAM	SETUP
	A/B	SELECT	SELECT	MONITOR	DIRECT	MIC	DIGITALIN
									S-VIDEO	VIDEO	L AUDIO R

Note

•The attenuator isn’t available with digital sources, or when using Stream Direct modes 2 or 3.

ACOUSTIC										TUNER	SBCH
CAL.	MIDNIGHT	LOUDNESS	TONE	OPTION			DIGITALNR	INPUT ATT	CLASS	STATION	MODE
PHONES	SPSYSTEM	SIGNAL	VIDEO	TAPE2	STREAM	SETUP			VIDEOINPUT
PHONES	SPSYSTEM	SIGNAL	VIDEO	TAPE2	STREAM	SETUP
	A/B	SELECT	SELECT	MONITOR	DIRECT	MIC	DIGITALIN
									S-VIDEO	VIDEO	L AUDIO R

2Use the (OPTION) +/– buttons to adjust the amount of delay.

The delay can be adjusted from 0.0–6.0 frames (in 0.1 frame steps).

3Press ENTER to confirm.

Note

•When listening to an analog source, you can’t use sound delay when Stream Direct is on.

•One second is equal to 30 frames of NTSC format video, and 25 frames of PAL.

75

En

Image 75

Contents VSX-AX10Ai-G Risk of Electric Shock Do not Open Operating EnvironmentInformation to User Voltage selectorContents Controlling other equipment Surround Setup menuUsing other functions Advanced setupOur philosophy FeaturesBefore you start Chapter Checking the supplied accessoriesUsing the remote control Before you startPress Calibrate Setting up the remote controlCalibrating the remote control screen Before you startSetting the clock Setting the button alert volumeSetting the time-out setting Press Reset to Default Resetting the remote controlLocking the remote control Restarting the remote controlReplacing the lithium-ion batteries Connecting your equipment Connecting your equipment ChapterRear panel When making cable connections Connecting your equipmentConnecting your equipment Connecting your TV Assignable Connecting your equipment Connecting a DVD playerConnecting the multichannel analog outputs STB VSX-AX10Ai Connecting your equipment Connecting a VCR or DVD recorderConnecting your equipment Connecting other video sources About the video converter Connecting your equipment Using the component video jacksConnecting your equipment Connecting digital audio sources Turntable Connecting your equipment Connecting analog audio sourcesPortable DVD player, etc Connecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsAM loop antenna Connecting your equipment Connecting antennasFM wire antenna Connecting external antennasPlugging in the receiver About the supplied AC power cordsControls and displays Chapter Controls and displaysTone Controls and displaysTuned Controls and displays DisplayControls and displays Remote control Basic remote control displaysHome menu screens Setup Receiver menu screensDigital NR Display Dimmer Remote control displays for the tunerDisp Mode Speaker A/BTV control menu screens Remote control displays for other componentsOperating menus for additional components 10 CLR Search ModeGetting started Chapter Automatically setting up for surround soundSwitch on the receiver and your TV Getting startedEnter Getting startedChecking the settings on your DVD or other player Other problems when using the Auto Surround SetupPlaying a source Change the receiver input to the source you want to play Listening in surround sound Listening to your systemListening to your system Chapter About the listening modesDolby Pro Logic IIx Music settings Neo6 Music settingsListening to your system Use the Option +/- buttons to adjust the effect level Using the Advanced surround effectsUsing the Home THX modes Adjusting the Advanced Surround effect levelPRO Logic NEO6 Cinema Listening with headphonesListening in stereo Pro Logic IIx MoviePress Multi CH Input on the remote control Home menu screen Using the Stream Direct modeAnalog Selecting the input signal typeListening to high-sampling formats Selecting USB and multichannel analog input channelsChannel Surround back channel options Listening to your system Using the surround back channelPress SB CH Mode repeatedly to cycle through AutoUse the Option +/- buttons to change the setting Creating a center speaker effectVSB Auto VSB on VSB OFF Switching the tone control on or off Listening to your system Using Hi-bit and Hi-samplingUsing Midnight and Loudness listening Using the tone controlAdjusting the bass and treble Reducing noise during playbackTreble Listening to your system Listening to dual mono soundtracks Changing the frequency step Using the tunerUsing the tuner Chapter Finding a stationUsing the tuner Tuning directly to a station Memorizing station presetsMPX mode Abcdefghijklmnopqrstuvwxyz Using the tunerListening to memorized station presets Naming station presetsSelect ‘Surround Setup’ then press Enter Surround Setup menuSurround Setup menu Chapter Making receiver settings from the Surround Setup menuSpeaker Systems Surround Setup menuLarge Select ‘Channel Level’ then press Enter Channel LevelAcoustic Calibration EQ Setting the Acoustic Calibration EQ automaticallySetting the Acoustic Calibration EQ manually Speaker DistanceSelect ‘Data Copy’ then press Enter Copying your Acoustic Calibration EQ settingsSelect ‘Manual’ then press Enter Select CUSTOM1 or CUSTOM2 then press EnterHow to use Professional Acoustic Calibration EQ How to interpret the graphical outputProfessional Acoustic Calibration EQ If you selected ‘Auto Pro.’, select ‘Start’ and press Using Professional Acoustic Calibration EQSelect a manual setup option and press Enter Select ‘Professional’ then press EnterSelect ‘X-Curve’ then press Enter Switch the X-Curve on or OFFCurve Use Cursor left/right buttons to selectChecking your surround settings Select ‘Check’ from the Surround Setup menu and press EnterCycle through the settings screen by screen Controlling other equipment Chapter Using the remote control with other componentsRecalling preset codes Controlling other equipmentControlling other equipment Select a setting typeProgramming signals from other remote controls Press Learning on the remote setup menuPioneer-1 DVR-7000 Press KEY Label on the remote setup menu Editing remote control button namesPress Direct Function on the remote setup menu Press OK to confirm the settingsPress OK when you’ve finished Select the button you want to renameChoose how you want to change the look of the button This will be the one that starts the multi operation when LD if the multi operation is being used to switch onFrom the ‘Select Function’ screen, choose Input functionMulti Operation Using multi operationsPress OK when you’re finished From the remote control Home menu pressSystem OFF Switching components on and offUsing the 12 volt trigger Using System offMonitoring your recording Using other functionsUsing other functions Chapter Making an audio or a video recordingUse the Option +/- buttons to adjust the amount of delay Adjusting the delay of a soundtrackPress Option repeatedly until Sacd Gain shows in the display Enhancing Sacd playbackDimming the display Using other functionsSwitching the speaker impedance Switch the SD1 Normal Stream Direct modeUsing other functions Checking your system settings Resetting the systemDefault receiver settings Bypass Other connections Using speaker system BSwitching the speaker system Using speaker system B in another roomSP B ITU-R is selected Select the ‘ITU-R’ setting from the Speaker Systems menuOther connections Bi-amping your front speakersBi-wiring your speakers Using the pre-outsConnecting additional amplifiers Connecting an external stereo pre-amplifier Using the i.LINK interfaceAbout i.LINK About Pqls rate controlCreating an i.LINK network Press ‘USB’ on the remote control Home menu Screen Using the USB interfaceConnecting a PC for Advanced Mcacc output Select ‘PC Output’ and press Enter Advanced Mcacc output using your PCInput Assign menu Advanced setupAdvanced setup Chapter Make sure your receiver and TV are both switched onAdvanced setup Assigning the component video inputsAssigning the i.LINK inputs Multi in OFF USB OFF Expert Setup menuSelect ‘Expert Setup’ then press Enter Assigning the video inputsBass Peak Level OSD AdjustmentDynamic Range Control Function RenameOSD Overlay THX Audio Setup Select ‘THX Audio Setup’ then press EnterVolt Trigger Surround Back Speaker Position THX Ultra2 Subwoofer SetupAdditional information Chapter Optimizing your speaker setupBasic surround setup Additional informationAdditional information THX speaker system setupAdditional information Troubleshooting PowerNo sound Listening in surround sound on Symptom Symptom Cause Other audio problemsVideo SettingsJack Remote controlSelect button DisplayLink messages Link interfaceMiscellaneous USB interfaceDolby Additional information Surround sound formatsAbout THX Windows Media Audio 9 ProfessionalPCM Pulse Code Modulation THX MusicMode Maintenance of external surfacesTHX Ultra2 Cinema mode Advanced Speaker Array ASAAdditional information Specifications 04B00001 ARB7292-A