Pioneer VSX-AX10Ai-G manual Symptom

Page 99

Additional information

12

Symptom

Sound is produced from analog components, but not from digital ones (DVD, LD, CD-ROM etc.).

Cause

Remedy

• The digital input assignment is wrong.

• Assign the digital inputs correctly (see Assigning the

 

digital inputs on page 88).

 

 

• The digital components aren't connected

• Make sure you have properly connected the digital

properly.

component to the corresponding input on the back of the

 

receiver (see Connecting your equipment on page 12).

 

• The player is not compatible with the source

• Choose a compatible source, or check the component’s

 

you're using, or the player settings are

manual for the correct settings.

 

incorrect.

 

 

 

 

 

• The digital output level has been turned

• Set the digital volume level of the player to full, or to the

 

down on a CD player or other component

neutral position.

 

equipped with digital output level adjustment

 

 

capability.

 

 

 

 

 

• Analog input has been selected.

• Select digital input (see Selecting the input signal type

 

 

on page 46).

 

 

 

When playing an LD the input

The LD is not a Dolby Digital compatible disc.

• Set the input signal to AUTO (see Selecting the input

signal type is 2RF but there is

 

signal type on page 46). Also make sure your LD player is

still no sound.

 

hooked up with analog connections in addition to digital

 

 

and 2RF connections (see Connecting other video

 

 

sources on page 19).

No sound output from the headphones.

The U-shaped connectors that connect the POWER AMP IN terminals to the front channel pre-outs are not connected.

•Reconnect the POWER AMP IN terminals to the front channel pre-outs using the supplied U-shaped connectors (see item 8 in Rear panel on page 12).

No sound is output or a noise is

• A DVD player not compatible with Dolby

• Make sure your DVD player is compatible with Dolby

output when Dolby Digital/DTS

Digital/DTS is being used.

Digital/DTS.

software is played back.

 

 

• The settings on the DVD player are incorrect

• Make sure the player's settings are correct and/or the

 

 

and/or the DTS signal output is turned off.

DTS signal out is on. Refer to the instruction manual

 

 

supplied with the DVD player.

 

 

 

 

• The digital output level is turned down on a

• Set the digital volume level of the player to full, or to the

 

CD player or other component equipped with

neutral position.

 

digital output level adjustment capability. (The

 

 

DTS signal has been altered by the player, and

 

 

cannot be read.)

 

 

 

 

No sound is output when the

• Incorrect frequency.

• Tune into the correct frequency.

AM/FM is selected.

 

 

• The antenna is not connected.

• Connect the antenna (see Connecting antennas on

 

 

 

page 26).

No digital output from the DVD player when playing a multichannel DVD-Audio or SACD disc.

•DVD players do not output digital audio when playing these kinds of discs.

•To enjoy fully multichannel DVD-Audio and SACD discs, connect your DVD player to this receiver through the multichannel analog inputs. See Connecting the multichannel analog outputs on page 16 and also the operating instructions that came with your DVD player.

No digital output when playing a • DVD players do not output digital audio at

• This is not a malfunction. To enjoy fully these discs,

192/176.4 kHz sampling rate

these sampling rates. Usually, players output

connect your DVD player to this receiver through the

DVD-Audio disc.

the audio from these discs at a downsampled

multichannel analog inputs. See Connecting the

 

rate of 96/88.2 kHz or 48/44.1 kHz. Some discs

multichannel analog outputs on page 16 and also the

 

prohibit all digital output.

operating instructions that came with your DVD player.

 

 

 

During playback of a Dolby

• The listening mode is not set correctly.

• Set the surround back channel to SB CH AUTO (see

Surround EX / DTS ES

 

Using the surround back channel on page 48).

soundtrack, the LS, S and RS

 

 

indicators light but there is no

 

 

surround back channel sound.

 

 

 

 

 

99

En

Page 98 Page 100
Image 99
Page 98 Page 100
Contents VSX-AX10Ai-G Risk of Electric Shock Do not Open Operating EnvironmentInformation to User Voltage selectorContents Controlling other equipment Surround Setup menuUsing other functions Advanced setupOur philosophy FeaturesBefore you start Chapter Checking the supplied accessoriesUsing the remote control Before you startPress Calibrate Setting up the remote controlCalibrating the remote control screen Before you startSetting the clock Setting the button alert volumeSetting the time-out setting Press Reset to Default Resetting the remote controlLocking the remote control Restarting the remote controlReplacing the lithium-ion batteries Connecting your equipment Connecting your equipment ChapterRear panel When making cable connections Connecting your equipmentConnecting your equipment Connecting your TV Assignable Connecting your equipment Connecting a DVD playerConnecting the multichannel analog outputs STB VSX-AX10Ai Connecting your equipment Connecting a VCR or DVD recorderConnecting your equipment Connecting other video sources About the video converter Connecting your equipment Using the component video jacksConnecting your equipment Connecting digital audio sources Turntable Connecting your equipment Connecting analog audio sourcesPortable DVD player, etc Connecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsAM loop antenna Connecting your equipment Connecting antennasFM wire antenna Connecting external antennasPlugging in the receiver About the supplied AC power cordsControls and displays Chapter Controls and displaysTone Controls and displaysTuned Controls and displays DisplayControls and displays Remote control Basic remote control displaysHome menu screens Setup Receiver menu screensDigital NR Display Dimmer Remote control displays for the tunerDisp Mode Speaker A/BTV control menu screens Remote control displays for other componentsOperating menus for additional components 10 CLR Search ModeGetting started Chapter Automatically setting up for surround soundSwitch on the receiver and your TV Getting startedEnter Getting startedChecking the settings on your DVD or other player Other problems when using the Auto Surround SetupPlaying a source Change the receiver input to the source you want to play Listening in surround sound Listening to your systemListening to your system Chapter About the listening modesDolby Pro Logic IIx Music settings Neo6 Music settingsListening to your system Use the Option +/- buttons to adjust the effect level Using the Advanced surround effectsUsing the Home THX modes Adjusting the Advanced Surround effect levelPRO Logic NEO6 Cinema Listening with headphonesListening in stereo Pro Logic IIx MoviePress Multi CH Input on the remote control Home menu screen Using the Stream Direct modeAnalog Selecting the input signal typeListening to high-sampling formats Selecting USB and multichannel analog input channelsChannel Surround back channel options Listening to your system Using the surround back channelPress SB CH Mode repeatedly to cycle through AutoUse the Option +/- buttons to change the setting Creating a center speaker effectVSB Auto VSB on VSB OFF Switching the tone control on or off Listening to your system Using Hi-bit and Hi-samplingUsing Midnight and Loudness listening Using the tone controlAdjusting the bass and treble Reducing noise during playbackTreble Listening to your system Listening to dual mono soundtracks Changing the frequency step Using the tunerUsing the tuner Chapter Finding a stationUsing the tuner Tuning directly to a station Memorizing station presetsMPX mode Abcdefghijklmnopqrstuvwxyz Using the tunerListening to memorized station presets Naming station presetsSelect ‘Surround Setup’ then press Enter Surround Setup menuSurround Setup menu Chapter Making receiver settings from the Surround Setup menuSpeaker Systems Surround Setup menuLarge Select ‘Channel Level’ then press Enter Channel LevelAcoustic Calibration EQ Setting the Acoustic Calibration EQ automaticallySetting the Acoustic Calibration EQ manually Speaker DistanceSelect ‘Data Copy’ then press Enter Copying your Acoustic Calibration EQ settingsSelect ‘Manual’ then press Enter Select CUSTOM1 or CUSTOM2 then press EnterHow to use Professional Acoustic Calibration EQ How to interpret the graphical outputProfessional Acoustic Calibration EQ If you selected ‘Auto Pro.’, select ‘Start’ and press Using Professional Acoustic Calibration EQSelect a manual setup option and press Enter Select ‘Professional’ then press EnterSelect ‘X-Curve’ then press Enter Switch the X-Curve on or OFFCurve Use Cursor left/right buttons to selectChecking your surround settings Select ‘Check’ from the Surround Setup menu and press EnterCycle through the settings screen by screen Controlling other equipment Chapter Using the remote control with other componentsRecalling preset codes Controlling other equipmentControlling other equipment Select a setting typeProgramming signals from other remote controls Press Learning on the remote setup menuPioneer-1 DVR-7000 Press KEY Label on the remote setup menu Editing remote control button namesPress Direct Function on the remote setup menu Press OK to confirm the settingsPress OK when you’ve finished Select the button you want to renameChoose how you want to change the look of the button This will be the one that starts the multi operation when LD if the multi operation is being used to switch onFrom the ‘Select Function’ screen, choose Input functionMulti Operation Using multi operationsPress OK when you’re finished From the remote control Home menu pressSystem OFF Switching components on and offUsing the 12 volt trigger Using System offMonitoring your recording Using other functionsUsing other functions Chapter Making an audio or a video recordingUse the Option +/- buttons to adjust the amount of delay Adjusting the delay of a soundtrackPress Option repeatedly until Sacd Gain shows in the display Enhancing Sacd playbackDimming the display Using other functionsSwitching the speaker impedance Switch the SD1 Normal Stream Direct modeUsing other functions Checking your system settings Resetting the systemDefault receiver settings Bypass Other connections Using speaker system BSwitching the speaker system Using speaker system B in another roomSP B ITU-R is selected Select the ‘ITU-R’ setting from the Speaker Systems menuOther connections Bi-amping your front speakersBi-wiring your speakers Using the pre-outsConnecting additional amplifiers Connecting an external stereo pre-amplifier Using the i.LINK interfaceAbout i.LINK About Pqls rate controlCreating an i.LINK network Press ‘USB’ on the remote control Home menu Screen Using the USB interfaceConnecting a PC for Advanced Mcacc output Select ‘PC Output’ and press Enter Advanced Mcacc output using your PCInput Assign menu Advanced setupAdvanced setup Chapter Make sure your receiver and TV are both switched onAdvanced setup Assigning the component video inputsAssigning the i.LINK inputs Multi in OFF USB OFF Expert Setup menuSelect ‘Expert Setup’ then press Enter Assigning the video inputsBass Peak Level OSD AdjustmentDynamic Range Control Function RenameOSD Overlay THX Audio Setup Select ‘THX Audio Setup’ then press EnterVolt Trigger Surround Back Speaker Position THX Ultra2 Subwoofer SetupAdditional information Chapter Optimizing your speaker setupBasic surround setup Additional informationAdditional information THX speaker system setupAdditional information Troubleshooting PowerNo sound Listening in surround sound on Symptom Symptom Cause Other audio problemsVideo SettingsJack Remote controlSelect button DisplayLink messages Link interfaceMiscellaneous USB interfaceDolby Additional information Surround sound formatsAbout THX Windows Media Audio 9 ProfessionalPCM Pulse Code Modulation THX MusicMode Maintenance of external surfacesTHX Ultra2 Cinema mode Advanced Speaker Array ASAAdditional information Specifications 04B00001 ARB7292-A
Top Page Image Contents