Pioneer VSX-AX10Ai-G manual Using multi operations, Press OK when you’re finished, Multi Operation

Page 72

08Controlling other equipment

•You don't need to program the receiver to switch to the input function selected in step 2, or to switch on or off. This is done automatically.

With Pioneer components, you don’t need to:

•program the power to switch off in a shutdown sequence;

•program the power to switch on if it’s the source component selected in step 2;

•program a Pioneer TV or monitor to switch on if the input function (selected in step 2) has video input terminals;

These take priority in multi operations (not shutdown).

5If necessary, add a delay between operations by pressing ‘Delay’.

Some components may take a few seconds to switch on or off, or perform certain operations. In these cases, you may want to add a slight delay (up to sixty seconds is possible) between commands.

Use the + and – buttons on the Delay Time screen to adjust the delay time then press OK.

DVD/LD

MULTI OPERATION

Delay Time

–

0.1 sec

+

OK CANCEL

•If you want to change the delay time after it’s been set, press the delay time, then press SET to come back to this screen.

6Repeat steps 3 to 5 for additional commands. As each command is entered, they will appear in order on the remote touch screen.

DVD/LD

MULTI OPERATION

DVD -

PLAY

Delay - 2.0sec

Add Replace Run

Delete Delay OK

•To add a new command above another command, press the existing command before pressing Add.

•To erase a command, select the operation you want to erase and press Delete.

•Commands will be stored regardless of how you exit from this screen.

7 Press OK when you’re finished.

PLEASE WAIT shows in the remote display while the multi operation is stored and you’ll return to step 2.

Using multi operations

You can start multi operations with the receiver switched on, or in standby.

1From the remote control Home menu press

MULTI OPERATION.

HOME 1/3

RECEIVER RECEIVER

INPUT 1

2

3

DVD

 

TV

SAT

/ LD

 

/ DVD

 

 

DVR

 

CD

TUNER

/ VCR1

 

 

 

 

TV

 

MULTI

SYSTEM

CONT

OPERATION

OFF

SETUP

2Press a function button that has been set up with a multi operation.

The receiver switches on (if it was in standby) and the programmed multi operation is performed automatically.

MULTI OPERATION

Select Function

DVD

TV

SAT

/ LD

/ DVD

 

DVR

CD

TUNER

/ VCR1

 

 

VCR2

VCR3

CD-R

/ TAPE1

 

 

VIDEO

MULTI CH

TV

INPUT

CONT

 

CANCEL

•To test the sequence before confirming it, press Run.

•To replace a command in the sequence, select the command then press Replace. Add the operation as shown in the steps above.

72

En

Page 71 Page 73
Image 72
Page 71 Page 73
Contents VSX-AX10Ai-G Operating Environment Risk of Electric Shock Do not OpenVoltage selector Information to UserContents Surround Setup menu Using other functionsAdvanced setup Controlling other equipmentFeatures Our philosophyChecking the supplied accessories Using the remote controlBefore you start Before you start ChapterSetting up the remote control Calibrating the remote control screenBefore you start Press CalibrateSetting the clock Setting the button alert volumeSetting the time-out setting Resetting the remote control Locking the remote controlRestarting the remote control Press Reset to DefaultReplacing the lithium-ion batteries Connecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsConnecting your equipment Connecting your TV Connecting your equipment Connecting a DVD player AssignableConnecting the multichannel analog outputs STB Connecting your equipment Connecting a VCR or DVD recorder VSX-AX10AiConnecting your equipment Connecting other video sources Connecting your equipment Using the component video jacks About the video converterConnecting your equipment Connecting digital audio sources Connecting your equipment Connecting analog audio sources TurntablePortable DVD player, etc Connecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting your equipment Connecting antennas FM wire antennaConnecting external antennas AM loop antennaAbout the supplied AC power cords Plugging in the receiverControls and displays Controls and displays ChapterControls and displays ToneControls and displays Display TunedControls and displays Remote control Basic remote control displaysHome menu screens Setup Receiver menu screensDigital NR Remote control displays for the tuner Disp ModeSpeaker A/B Display DimmerRemote control displays for other components TV control menu screensOperating menus for additional components Search Mode 10 CLRAutomatically setting up for surround sound Switch on the receiver and your TVGetting started Getting started ChapterGetting started EnterChecking the settings on your DVD or other player Other problems when using the Auto Surround SetupPlaying a source Change the receiver input to the source you want to play Listening to your system Listening to your system ChapterAbout the listening modes Listening in surround soundDolby Pro Logic IIx Music settings Neo6 Music settingsListening to your system Using the Advanced surround effects Using the Home THX modesAdjusting the Advanced Surround effect level Use the Option +/- buttons to adjust the effect levelListening with headphones Listening in stereoPro Logic IIx Movie PRO Logic NEO6 CinemaUsing the Stream Direct mode Press Multi CH Input on the remote control Home menu screenSelecting the input signal type AnalogListening to high-sampling formats Selecting USB and multichannel analog input channelsChannel Listening to your system Using the surround back channel Press SB CH Mode repeatedly to cycle throughAuto Surround back channel optionsUse the Option +/- buttons to change the setting Creating a center speaker effectVSB Auto VSB on VSB OFF Listening to your system Using Hi-bit and Hi-sampling Using Midnight and Loudness listeningUsing the tone control Switching the tone control on or offAdjusting the bass and treble Reducing noise during playbackTreble Listening to your system Listening to dual mono soundtracks Using the tuner Using the tuner ChapterFinding a station Changing the frequency stepUsing the tuner Tuning directly to a station Memorizing station presetsMPX mode Using the tuner Listening to memorized station presetsNaming station presets AbcdefghijklmnopqrstuvwxyzSurround Setup menu Surround Setup menu ChapterMaking receiver settings from the Surround Setup menu Select ‘Surround Setup’ then press EnterSurround Setup menu Speaker SystemsLarge Channel Level Select ‘Channel Level’ then press EnterSetting the Acoustic Calibration EQ automatically Setting the Acoustic Calibration EQ manuallySpeaker Distance Acoustic Calibration EQCopying your Acoustic Calibration EQ settings Select ‘Manual’ then press EnterSelect CUSTOM1 or CUSTOM2 then press Enter Select ‘Data Copy’ then press EnterHow to use Professional Acoustic Calibration EQ How to interpret the graphical outputProfessional Acoustic Calibration EQ Using Professional Acoustic Calibration EQ Select a manual setup option and press EnterSelect ‘Professional’ then press Enter If you selected ‘Auto Pro.’, select ‘Start’ and pressSwitch the X-Curve on or OFF CurveUse Cursor left/right buttons to select Select ‘X-Curve’ then press EnterChecking your surround settings Select ‘Check’ from the Surround Setup menu and press EnterCycle through the settings screen by screen Using the remote control with other components Recalling preset codesControlling other equipment Controlling other equipment ChapterSelect a setting type Controlling other equipmentProgramming signals from other remote controls Press Learning on the remote setup menuPioneer-1 DVR-7000 Editing remote control button names Press Direct Function on the remote setup menuPress OK to confirm the settings Press KEY Label on the remote setup menuPress OK when you’ve finished Select the button you want to renameChoose how you want to change the look of the button LD if the multi operation is being used to switch on From the ‘Select Function’ screen, chooseInput function This will be the one that starts the multi operation whenUsing multi operations Press OK when you’re finishedFrom the remote control Home menu press Multi OperationSwitching components on and off Using the 12 volt triggerUsing System off System OFFUsing other functions Using other functions ChapterMaking an audio or a video recording Monitoring your recordingAdjusting the delay of a soundtrack Use the Option +/- buttons to adjust the amount of delayEnhancing Sacd playback Press Option repeatedly until Sacd Gain shows in the displayUsing other functions Switching the speaker impedanceSwitch the SD1 Normal Stream Direct mode Dimming the displayUsing other functions Checking your system settings Resetting the systemDefault receiver settings Bypass Using speaker system B Switching the speaker systemUsing speaker system B in another room Other connectionsSelect the ‘ITU-R’ setting from the Speaker Systems menu Other connectionsBi-amping your front speakers SP B ITU-R is selectedBi-wiring your speakers Using the pre-outsConnecting additional amplifiers Using the i.LINK interface Connecting an external stereo pre-amplifierAbout i.LINK About Pqls rate controlCreating an i.LINK network Using the USB interface Press ‘USB’ on the remote control Home menu ScreenConnecting a PC for Advanced Mcacc output Advanced Mcacc output using your PC Select ‘PC Output’ and press EnterAdvanced setup Advanced setup ChapterMake sure your receiver and TV are both switched on Input Assign menuAdvanced setup Assigning the component video inputsAssigning the i.LINK inputs Expert Setup menu Select ‘Expert Setup’ then press EnterAssigning the video inputs Multi in OFF USB OFFOSD Adjustment Bass Peak LevelDynamic Range Control Function RenameOSD Overlay THX Audio Setup Select ‘THX Audio Setup’ then press EnterVolt Trigger THX Ultra2 Subwoofer Setup Surround Back Speaker PositionOptimizing your speaker setup Basic surround setupAdditional information Additional information ChapterTHX speaker system setup Additional informationAdditional information Troubleshooting PowerNo sound Listening in surround sound on Symptom Other audio problems Symptom CauseSettings VideoRemote control JackDisplay Select buttonLink interface Link messagesUSB interface MiscellaneousAdditional information Surround sound formats DolbyAbout THX Windows Media Audio 9 ProfessionalPCM Pulse Code Modulation Maintenance of external surfaces THX Ultra2 Cinema modeAdvanced Speaker Array ASA THX MusicModeAdditional information Specifications 04B00001 ARB7292-A
Top Page Image Contents