Pioneer VSX-AX10Ai-G manual Other connections Chapter, Using speaker system B

Page 80

10Other connections

Chapter 10

Other connections

Caution

•Before making or changing the connections, switch off the power and disconnect the power cord from the power outlet. Plugging in components should be the last connection you make with your system.

•Be careful not to allow any contact between speaker wires from different terminals.

•Note that the + and – connections on speaker terminals A and B are in opposite positions.

•You can use speakers with a nominal impedance between 4–16Ω(please see Switching the speaker impedance on page 77 if you plan to use speakers with an impedance of less than 6Ω).

Using speaker system B

You can connect a pair of speakers to the B speaker terminals on the rear panel to listen to stereo playback in another room, or you can also use these terminals to hear surround sound when playing DVD-Audio sources. Once you’ve made these connections, you’ll have to change the speaker setting in Speaker Systems on page 57 to specify how you’re using speaker system B.

Switching the speaker system

This unit has three speaker system settings which allow you to select the speaker system(s) you want to use. What you will hear depends on the settings you made in Speaker Systems on page 57. If you selected Normal Surround for speaker system A, and Second Zone for speaker system B, sound is output according to the explanations below.

•Use the SPEAKER A/B button on the remote control receiver menu screen to select a speaker system setting.

You can also use the front panel SP SYSTEM A/B button.

RECEIVER 3/3

TV

RECEIVER CONT

INPUT

SB CH

MODE

SPEAKER

INPUT

A/B

ATT

VIDEO

DISPLAY

SELECT

DIMMER

TAPE2

STATUS

MONITOR

ACOUSTIC

 

 

 

 

 

 

 

 

 

TUNER

SBCH

CAL.

MIDNIGHT

LOUDNESS

TONE

OPTION

 

 

DIGITALNR

INPUT ATT

CLASS

STATION

MODE

PHONES

SPSYSTEM

SIGNAL

VIDEO

TAPE2

STREAM

SETUP

 

 

VIDEOINPUT

 

 

 

 

 

 

 

A/B

SELECT

SELECT

MONITOR

DIRECT

MIC

DIGITALIN

 

 

 

 

 

 

 

 

 

 

 

 

 

S-VIDEO

VIDEO

L AUDIO R

Press repeatedly to cycle through the speaker system options:

• SP A – Sound is output from speaker system A and the same signal is output from the pre-out terminals.

• SP B – Sound is output from the two speakers connected to speaker system B. Multichannel sources will be downmixed to these two speakers. The same signal is output from the surround back channel pre-out terminals.

• SP AB – Sound is output from speaker system A (up to 5 channels, depending on the source), the two speakers in speaker system B, and the subwoofer. The sound from speaker system B will be the same as the sound from speaker system A (multichannel sources will be downmixed to 2 channels). The same signal as speaker A is output from the pre-out terminals, except for the surround back pre-outs, which output the same signal as speaker B.

•SP (off) – No sound is output from the speakers. The same sound is output from the pre-out terminals as when selecting speaker system A (above).

Note

• The subwoofer output depends on the settings you made in Speaker Systems on page 57. However, if SP B is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed).

•Depending on the settings in Speaker Systems on page 57 and Using the Stream Direct mode on page 45, output from the surround back pre-out terminals may change.

•All speaker systems are switched off when headphones are connected.

Using speaker system B in another room

Connect a pair of speakers to the speaker B terminals on the rear panel the same way you connected your speakers in Connecting the speakers on page 24. Make sure to review Placing the speakers on page 25 when placing the speakers in another room.

80

En

Page 79 Page 81
Image 80
Page 79 Page 81
Contents VSX-AX10Ai-G Operating Environment Risk of Electric Shock Do not OpenVoltage selector Information to UserContents Surround Setup menu Using other functionsAdvanced setup Controlling other equipmentFeatures Our philosophyChecking the supplied accessories Using the remote controlBefore you start Before you start ChapterSetting up the remote control Calibrating the remote control screenBefore you start Press CalibrateSetting the time-out setting Setting the clockSetting the button alert volume Resetting the remote control Locking the remote controlRestarting the remote control Press Reset to DefaultReplacing the lithium-ion batteries Rear panel Connecting your equipmentConnecting your equipment Chapter Connecting your equipment When making cable connectionsConnecting your equipment Connecting your TV Connecting your equipment Connecting a DVD player AssignableConnecting the multichannel analog outputs STB Connecting your equipment Connecting a VCR or DVD recorder VSX-AX10AiConnecting your equipment Connecting other video sources Connecting your equipment Using the component video jacks About the video converterConnecting your equipment Connecting digital audio sources Connecting your equipment Connecting analog audio sources TurntablePortable DVD player, etc Connecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting your equipment Connecting antennas FM wire antennaConnecting external antennas AM loop antennaAbout the supplied AC power cords Plugging in the receiverControls and displays Controls and displays ChapterControls and displays ToneControls and displays Display TunedHome menu screens Controls and displays Remote controlBasic remote control displays Digital NR SetupReceiver menu screens Remote control displays for the tuner Disp ModeSpeaker A/B Display DimmerRemote control displays for other components TV control menu screensOperating menus for additional components Search Mode 10 CLRAutomatically setting up for surround sound Switch on the receiver and your TVGetting started Getting started ChapterGetting started EnterPlaying a source Checking the settings on your DVD or other playerOther problems when using the Auto Surround Setup Change the receiver input to the source you want to play Listening to your system Listening to your system ChapterAbout the listening modes Listening in surround soundListening to your system Dolby Pro Logic IIx Music settingsNeo6 Music settings Using the Advanced surround effects Using the Home THX modesAdjusting the Advanced Surround effect level Use the Option +/- buttons to adjust the effect levelListening with headphones Listening in stereoPro Logic IIx Movie PRO Logic NEO6 CinemaUsing the Stream Direct mode Press Multi CH Input on the remote control Home menu screenSelecting the input signal type AnalogChannel Listening to high-sampling formatsSelecting USB and multichannel analog input channels Listening to your system Using the surround back channel Press SB CH Mode repeatedly to cycle throughAuto Surround back channel optionsVSB Auto VSB on VSB OFF Use the Option +/- buttons to change the settingCreating a center speaker effect Listening to your system Using Hi-bit and Hi-sampling Using Midnight and Loudness listeningUsing the tone control Switching the tone control on or offTreble Adjusting the bass and trebleReducing noise during playback Listening to your system Listening to dual mono soundtracks Using the tuner Using the tuner ChapterFinding a station Changing the frequency stepMPX mode Using the tuner Tuning directly to a stationMemorizing station presets Using the tuner Listening to memorized station presetsNaming station presets AbcdefghijklmnopqrstuvwxyzSurround Setup menu Surround Setup menu ChapterMaking receiver settings from the Surround Setup menu Select ‘Surround Setup’ then press EnterSurround Setup menu Speaker SystemsLarge Channel Level Select ‘Channel Level’ then press EnterSetting the Acoustic Calibration EQ automatically Setting the Acoustic Calibration EQ manuallySpeaker Distance Acoustic Calibration EQCopying your Acoustic Calibration EQ settings Select ‘Manual’ then press EnterSelect CUSTOM1 or CUSTOM2 then press Enter Select ‘Data Copy’ then press EnterProfessional Acoustic Calibration EQ How to use Professional Acoustic Calibration EQHow to interpret the graphical output Using Professional Acoustic Calibration EQ Select a manual setup option and press EnterSelect ‘Professional’ then press Enter If you selected ‘Auto Pro.’, select ‘Start’ and pressSwitch the X-Curve on or OFF CurveUse Cursor left/right buttons to select Select ‘X-Curve’ then press EnterCycle through the settings screen by screen Checking your surround settingsSelect ‘Check’ from the Surround Setup menu and press Enter Using the remote control with other components Recalling preset codesControlling other equipment Controlling other equipment ChapterSelect a setting type Controlling other equipmentPioneer-1 DVR-7000 Programming signals from other remote controlsPress Learning on the remote setup menu Editing remote control button names Press Direct Function on the remote setup menuPress OK to confirm the settings Press KEY Label on the remote setup menuChoose how you want to change the look of the button Press OK when you’ve finishedSelect the button you want to rename LD if the multi operation is being used to switch on From the ‘Select Function’ screen, chooseInput function This will be the one that starts the multi operation whenUsing multi operations Press OK when you’re finishedFrom the remote control Home menu press Multi OperationSwitching components on and off Using the 12 volt triggerUsing System off System OFFUsing other functions Using other functions ChapterMaking an audio or a video recording Monitoring your recordingAdjusting the delay of a soundtrack Use the Option +/- buttons to adjust the amount of delayEnhancing Sacd playback Press Option repeatedly until Sacd Gain shows in the displayUsing other functions Switching the speaker impedanceSwitch the SD1 Normal Stream Direct mode Dimming the displayDefault receiver settings Using other functions Checking your system settingsResetting the system Bypass Using speaker system B Switching the speaker systemUsing speaker system B in another room Other connectionsSelect the ‘ITU-R’ setting from the Speaker Systems menu Other connectionsBi-amping your front speakers SP B ITU-R is selectedConnecting additional amplifiers Bi-wiring your speakersUsing the pre-outs Using the i.LINK interface Connecting an external stereo pre-amplifierCreating an i.LINK network About i.LINKAbout Pqls rate control Using the USB interface Press ‘USB’ on the remote control Home menu ScreenConnecting a PC for Advanced Mcacc output Advanced Mcacc output using your PC Select ‘PC Output’ and press EnterAdvanced setup Advanced setup ChapterMake sure your receiver and TV are both switched on Input Assign menuAssigning the i.LINK inputs Advanced setupAssigning the component video inputs Expert Setup menu Select ‘Expert Setup’ then press EnterAssigning the video inputs Multi in OFF USB OFFOSD Adjustment Bass Peak LevelOSD Overlay Dynamic Range ControlFunction Rename Volt Trigger THX Audio SetupSelect ‘THX Audio Setup’ then press Enter THX Ultra2 Subwoofer Setup Surround Back Speaker PositionOptimizing your speaker setup Basic surround setupAdditional information Additional information ChapterTHX speaker system setup Additional informationNo sound Additional information TroubleshootingPower Listening in surround sound on Symptom Other audio problems Symptom CauseSettings VideoRemote control JackDisplay Select buttonLink interface Link messagesUSB interface MiscellaneousAdditional information Surround sound formats DolbyPCM Pulse Code Modulation About THXWindows Media Audio 9 Professional Maintenance of external surfaces THX Ultra2 Cinema modeAdvanced Speaker Array ASA THX MusicModeAdditional information Specifications 04B00001 ARB7292-A
Top Page Image Contents