Pioneer VSX-917V-S/-K manual 02 5 minute guide, Follow the instructions on-screen, Enter

Page 10

025 minute guide

6Follow the instructions on-screen.

•Make sure the microphone is connected.

•If you’re using a subwoofer, it is automatically detected every time you switch on the system. Make sure it is on and the volume is turned up.

•See below for notes regarding background noise and other possible interference.

7Wait for the test tones to finish.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present in your setup. Try to be as quiet as possible while it’s doing this.

2.Auto MCACC

Now Analyzing

 

 

 

 

 

Environment Check

 

Ambient Noise

[ OK ]

Microphone

[ OK ]

Speaker YES/NO

[ OK ]

 

 

 

:Cancel

•For correct speaker settings, do not adjust the volume during the test tones.

8Confirm the speaker configuration. The configuration shown on-screen should reflect the actual speakers you have.

2.Auto MCACC

 

Check!

Front

[ YES ]

 

Center

[ YES ]

 

Surround

[ YES ]

 

SB

[ Yx2 ]

 

SUB W.

[ YES ]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OK

30:Next

 

 

:Cancel

 

If the speaker configuration displayed isn’t

correct, use to select the speaker and to change the setting (and number for

surround back). When you’re finished, go to the next step.

If you see an error message (ERR) in the right side column, there may be a problem with the speaker connection. If selecting RETRY doesn’t fix the problem, turn off the power and check the speaker connections.

9Make sure ‘OK’ is selected, then press

ENTER.

If the screen in step 8 is left untouched for 30 seconds, and the ENTER button is not pressed in step 9 the Auto MCACC setup will start again from the beginning.

A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum receiver settings for channel level, speaker distance, and Acoustic Calibration EQ.

2.Auto MCACC

Now

Analyzing

 

 

 

 

 

 

 

 

 

Surround

Analyzing

 

 

Speaker

System

[

]

Speaker

Distance

[

]

Channel

Level

[

]

Acoustic

Cal EQ

[

]

:Cancel

Again, try to be as quiet as possible while this is happening. It may take 3 to 8 minutes.

10The Auto MCACC Setup has finished! Select ‘SKIP’ to go back to the System Setup menu.

The MCACC indicator on the front panel will light to show the setup is complete.

The settings made in the Auto MCACC Setup should give you excellent surround sound from your system, but it is also possible to adjust these settings manually using the System

Setup menu (starting on page 38).1

You can also choose to view the settings by selecting individual parameters from the Analyzed Data Check screen:

Note

1• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm will end up with different size settings. You can correct the setting manually using the Speaker Setting on page 44.

•The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and room characteristics into account) and generally does not need to be changed.

10

En

Page 9 Page 11
Image 10
Page 9 Page 11
Contents VSX-917V-S/-K Important the Moulded Plug Risk of Electric Shock Do not OpenVentilation Caution Voltage selectorOperating Environment Contents Controlling the rest of your system Other SettingsMaking recordings Other connectionsBefore you start Chapter Installing the receiverBefore you start Checking what’s in the boxBefore you start Ventilation Introduction to home theater Minute guide02 5 minute guide Chapter Listening to Surround SoundNederlands Español Minute guideMake sure ‘Normal SB’ is selected Then press EnterWait for the test tones to finish 02 5 minute guideFollow the instructions on-screen Make sure ‘OK’ is selected, then pressOther problems when using the Auto Mcacc Setup Better sound using Phase ControlPress Phase Phase Control to switch on phase correction Connecting up Chapter Connecting upMaking cable connections Connecting up About the video converter Connect the analog audio outputs from Connecting up Connecting a DVD player and TVThis receiver to a video input on your TV Audio and Video inputs on this receiver.2 Connecting upConnecting the multichannel analog outputs Digital OPT 2 TV/SAT input on thisConnecting other audio components About the WMA9 Pro decoderConnecting other video components Use a coaxial digital audio cable for the connection.3Connecting to the front panel audio mini jack Using the component video jacksConnecting to the front panel video terminal Use a three-way component video cable for the connectionTo improve FM reception Connecting up Connecting antennasUsing external antennas To improve AM receptionConnecting up Connecting the speakers This receiver PoweredHints on speaker placement View of 7.1 channel speaker setup Overhead view of speaker setupYou can also refer to the 3-D speaker setup illustration on Front panel Controls and displaysControls and displays Chapter STANDBY/ONControls and displays DisplayDirect DigitalVIR.SB Auto SurrMulti Control buttons Controls and displays Remote controlReceiver Number buttons / other component and receiver controlsTV Control buttons ADV.SURR Use to switch between the various surround modes5TUNE/ST +/- /ENTER Component control buttonsOperating range of remote control Auto playback Listening to your systemListening to your system Chapter Listening in surround soundSetting What it does Setting the effect optionsUsing the Advanced surround effects Listening to your systemListening in stereo Using Stream DirectUsing Front Stage Surround Advance STEREO/F.S.SURR to select Front StageUsing Virtual Surround Back VSB Using surround back channel processingListening with Acoustic Calibration EQ Using the Sound Retriever Using Midnight and LoudnessVirtual surround back channel option Listening to your system Enhancing dialog Using the tone controlsChoosing the input signal Playing other sourcesSelecting the front audio inputs Press F.AUDIO SHIFT+DVD on the remote controlPlayback the connected component USB playback Chapter Using the USB interfaceUSB playback Basic playback controlsOther compatibility information USB playbackCompressed audio compatibility About MPEG-4 AACSurround back speaker setting System Setup menuSystem Setup menu Chapter Select the setting you want to adjustSystem Setup menu Manual Mcacc speaker setupFine Channel Level Select ‘Fine Ch Level’ from the Manual Mcacc setup menuSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Fine Speaker DistanceSetting the Acoustic Calibration EQ Automatically Acoustic Calibration EQSelect ‘EQ Data Copy’ from the Manual Mcacc setup menu Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Select ‘OK’ to copy and confirmManual speaker setup Checking your Acoustic Calibration EQ settingsSpeaker Setting Manual SP Setup menuCrossover Network Default setting 100HzSelect ‘Crossover Network’ from the Manual SP Setup menu Channel LevelSpeaker Distance Saving station presets Using the tunerUsing the tuner Chapter Listening to the radioListening to station presets Using the tunerNaming station presets Changing the frequency stepMaking recordings Chapter Making recordingsMaking an audio or a video recording Controlling the rest of your system Chapter Setting the remote to control other componentsControlling the rest of your system Operating other Pioneer componentsName from the list then press Enter Erasing all of the remote control presetsUse Press and hold Enter for about two secondsLCD shows OK to confirm the setting Confirming preset codesUse to switch direct function on or OFF then press Enter Controlling the rest of your system Direct functionControlling the rest of your system Controls for TVs Disc Menu Controlling the rest of your systemControls for other components TOP MenuREC Stop RECSHIFT+ DiscDVD Shift HDD Shift+ CH + CH+Other connections Connecting using HdmiOther connections Chapter Other connections Second Zone speaker B setupSwitching the speaker system About HdmiBi-amping your front speakers Other connections Bi-wiring your speakers Same terminal in this wayDisplay Using the SR+ mode with a Pioneer plasma displayPioneer plasma DVD player Satellite receiver, etcInput Assign menu Other SettingsOther Settings Chapter Assigning the digital inputsOther Setup menu Other SettingsAssigning the Hdmi inputs Dual Mono Setup Dynamic Range Control SetupLFE Attenuator Setup Select ‘SR+ Setup’ from the Other Setup menu SR+ Setup for Pioneer plasma displaysDigital Video Converter Setup Select the ‘PDP Volume Control’ setting you wantAdditional information TroubleshootingProblemRemedy Additional information ChapterProblem Remedy Additional informationSymptom Remedy See Operating other Pioneer components onChanging the TV format setting Additional information Resetting the main unitSwitching the speaker impedance Press Setup to confirmAdditional information Specifications AM Tuner Section Power cord cautionCleaning the unit MiscellaneousPioneer Corporation
Top Page Image Contents