Pioneer VSX-917V-S/-K Controlling the rest of your system, Operating other Pioneer components

Page 50

10Controlling the rest of your system

Chapter 10:

Controlling the rest of your system

Operating other Pioneer components

Many Pioneer components have SR CONTROL jacks which can be used to link components together so that you can use just the remote sensor of one component. When you use a remote control, the control signal is passed along the chain to the appropriate

component.1

Note that if you use this feature, make sure that you also have at least one set of analog audio, video jacks or HDMI connected to another component for grounding purposes.

Setting the remote to control other components

Most components can be assigned to one of the MULTI CONTROL buttons using the component’s manufacturer preset code stored in the remote.

However, please note that there are cases where only certain functions may be controllable after assigning the proper preset code, or the codes for the manufacturer in the remote control will not work for the model that

you are using.2

	CONTROL
OUT	IN
	IN
CONTROL
IN	OUT
Receiver
	Other Pioneer products
Remote	with CONTROL terminals
control	Connect to CONTROL
unit	Connect to CONTROL
	terminal of other
	Pioneer products

Note

•You can cancel or exit any of the steps by pressing RECEIVER. To go back a step, press RETURN.

•After one minute of inactivity, the remote automatically exits the operation.

Note

1• If you want to control all your components using this receiver’s remote control, refer to Controlling the rest of your system on page 50.

•If you have connected a remote control to the CONTROL IN jack (using a mini-plug cable), you won’t be able to control this unit using the remote sensor.

2TV codes (for example, codes for TV, CATV, Satellite TV or DTV) can only be assigned to the TV/SAT or TV CTRL button.

50

En

Image 50

Contents VSX-917V-S/-K Important the Moulded Plug Risk of Electric Shock Do not OpenOperating Environment Voltage selectorVentilation Caution Contents Controlling the rest of your system Other SettingsMaking recordings Other connectionsBefore you start Chapter Installing the receiverBefore you start Checking what’s in the boxBefore you start Ventilation Introduction to home theater Minute guide02 5 minute guide Chapter Listening to Surround SoundNederlands Español Minute guideMake sure ‘Normal SB’ is selected Then press EnterWait for the test tones to finish 02 5 minute guideFollow the instructions on-screen Make sure ‘OK’ is selected, then pressPress Phase Phase Control to switch on phase correction Better sound using Phase ControlOther problems when using the Auto Mcacc Setup Making cable connections Connecting upConnecting up Chapter Connecting up About the video converter This receiver to a video input on your TV Connecting up Connecting a DVD player and TVConnect the analog audio outputs from Audio and Video inputs on this receiver.2 Connecting upConnecting the multichannel analog outputs Digital OPT 2 TV/SAT input on thisConnecting other audio components About the WMA9 Pro decoderConnecting other video components Use a coaxial digital audio cable for the connection.3Connecting to the front panel audio mini jack Using the component video jacksConnecting to the front panel video terminal Use a three-way component video cable for the connectionTo improve FM reception Connecting up Connecting antennasUsing external antennas To improve AM receptionConnecting up Connecting the speakers This receiver PoweredHints on speaker placement You can also refer to the 3-D speaker setup illustration on Overhead view of speaker setupView of 7.1 channel speaker setup Front panel Controls and displaysControls and displays Chapter STANDBY/ONControls and displays DisplayDirect DigitalVIR.SB Auto SurrMulti Control buttons Controls and displays Remote controlReceiver Number buttons / other component and receiver controlsTV Control buttons ADV.SURR Use to switch between the various surround modes5TUNE/ST +/- /ENTER Component control buttonsOperating range of remote control Auto playback Listening to your systemListening to your system Chapter Listening in surround soundSetting What it does Setting the effect optionsUsing the Advanced surround effects Listening to your systemListening in stereo Using Stream DirectUsing Front Stage Surround Advance STEREO/F.S.SURR to select Front StageListening with Acoustic Calibration EQ Using surround back channel processingUsing Virtual Surround Back VSB Virtual surround back channel option Using Midnight and LoudnessUsing the Sound Retriever Listening to your system Enhancing dialog Using the tone controlsChoosing the input signal Playing other sourcesPlayback the connected component Press F.AUDIO SHIFT+DVD on the remote controlSelecting the front audio inputs USB playback Chapter Using the USB interfaceUSB playback Basic playback controlsOther compatibility information USB playbackCompressed audio compatibility About MPEG-4 AACSurround back speaker setting System Setup menuSystem Setup menu Chapter Select the setting you want to adjustSystem Setup menu Manual Mcacc speaker setupFine Channel Level Select ‘Fine Ch Level’ from the Manual Mcacc setup menuSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Fine Speaker DistanceSetting the Acoustic Calibration EQ Automatically Acoustic Calibration EQSelect ‘EQ Data Copy’ from the Manual Mcacc setup menu Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Select ‘OK’ to copy and confirmManual speaker setup Checking your Acoustic Calibration EQ settingsSpeaker Setting Manual SP Setup menuCrossover Network Default setting 100HzSelect ‘Crossover Network’ from the Manual SP Setup menu Channel LevelSpeaker Distance Saving station presets Using the tunerUsing the tuner Chapter Listening to the radioListening to station presets Using the tunerNaming station presets Changing the frequency stepMaking an audio or a video recording Making recordingsMaking recordings Chapter Controlling the rest of your system Chapter Setting the remote to control other componentsControlling the rest of your system Operating other Pioneer componentsName from the list then press Enter Erasing all of the remote control presetsUse Press and hold Enter for about two secondsLCD shows OK to confirm the setting Confirming preset codesUse to switch direct function on or OFF then press Enter Controlling the rest of your system Direct functionControlling the rest of your system Controls for TVs Disc Menu Controlling the rest of your systemControls for other components TOP MenuREC Stop RECSHIFT+ DiscDVD Shift HDD Shift+ CH + CH+Other connections Chapter Connecting using HdmiOther connections Other connections Second Zone speaker B setupSwitching the speaker system About HdmiBi-amping your front speakers Other connections Bi-wiring your speakers Same terminal in this wayDisplay Using the SR+ mode with a Pioneer plasma displayPioneer plasma DVD player Satellite receiver, etcInput Assign menu Other SettingsOther Settings Chapter Assigning the digital inputsAssigning the Hdmi inputs Other SettingsOther Setup menu LFE Attenuator Setup Dynamic Range Control SetupDual Mono Setup Select ‘SR+ Setup’ from the Other Setup menu SR+ Setup for Pioneer plasma displaysDigital Video Converter Setup Select the ‘PDP Volume Control’ setting you wantAdditional information TroubleshootingProblemRemedy Additional information ChapterProblem Remedy Additional informationSymptom Remedy See Operating other Pioneer components onChanging the TV format setting Additional information Resetting the main unitSwitching the speaker impedance Press Setup to confirmAdditional information Specifications AM Tuner Section Power cord cautionCleaning the unit MiscellaneousPioneer Corporation