Pioneer VSX-917V-S/-K Connecting up Connecting antennas, Using external antennas, Indoor antenna

Page 19

Connecting up

03

Connecting antennas

Connect the AM loop antenna and the FM wire antenna as shown below. To improve reception and sound quality, connect external antennas (see Using external antennas below).

fig. a fig. bfig. c

3

FM UNBAL

5	75 Ω
	AM	4
	LOOP	4
	LOOP

1

2

1Pull off the protective shields of both AM antenna wires.

2Push open the tabs, then insert one wire fully into each terminal, then release the tabs to secure the AM antenna wires.

3Fix the AM loop antenna to the attached stand.

To fix the stand to the antenna, bend in the direction indicated by the arrow (fig. a) then clip the loop onto the stand (fig. b).

•If you plan to mount the AM antenna to a wall or other surface, secure the stand with screws (fig. c) before clipping the loop to the stand. Make sure the reception is clear.

4Place the AM antenna on a flat surface and in a direction giving the best reception.

5Connect the FM wire antenna in the same way as the AM loop antenna.

For best results, extend the FM antenna fully and fix to a wall or door frame. Don’t drape loosely or leave coiled up.

Using external antennas

To improve FM reception

Connect an external FM antenna as shown below.

75 Ω coaxial cable

FM UNBAL 75 Ω

J-shaped plug

AM

LOOP

To improve AM reception

Connect a 5 m to 6 m length of vinyl-coated wire to the AM antenna terminal without disconnecting the supplied AM loop antenna.

For the best possible reception, suspend horizontally outdoors.

Outdoor antenna

	5 m to 6 m
	Indoor antenna
75 Ω	(vinyl-coated wire)
FM UNBAL
AM
LOOP

English Deutsch Français Italiano Nederlands Español

19

En

Image 19

Contents VSX-917V-S/-K Risk of Electric Shock Do not Open Important the Moulded PlugVentilation Caution Voltage selectorOperating Environment Contents Other connections Other SettingsMaking recordings Controlling the rest of your systemChecking what’s in the box Installing the receiverBefore you start Before you start ChapterBefore you start Ventilation Listening to Surround Sound Minute guide02 5 minute guide Chapter Introduction to home theaterThen press Enter Minute guideMake sure ‘Normal SB’ is selected Nederlands EspañolMake sure ‘OK’ is selected, then press 02 5 minute guideFollow the instructions on-screen Wait for the test tones to finishOther problems when using the Auto Mcacc Setup Better sound using Phase ControlPress Phase Phase Control to switch on phase correction Connecting up Chapter Connecting upMaking cable connections Connecting up About the video converter Connect the analog audio outputs from Connecting up Connecting a DVD player and TVThis receiver to a video input on your TV Digital OPT 2 TV/SAT input on this Connecting upConnecting the multichannel analog outputs Audio and Video inputs on this receiver.2About the WMA9 Pro decoder Connecting other audio componentsUse a coaxial digital audio cable for the connection.3 Connecting other video componentsUse a three-way component video cable for the connection Using the component video jacksConnecting to the front panel video terminal Connecting to the front panel audio mini jackTo improve AM reception Connecting up Connecting antennasUsing external antennas To improve FM receptionThis receiver Powered Connecting up Connecting the speakersHints on speaker placement View of 7.1 channel speaker setup Overhead view of speaker setupYou can also refer to the 3-D speaker setup illustration on STANDBY/ON Controls and displaysControls and displays Chapter Front panelDisplay Controls and displaysAuto Surr DigitalVIR.SB DirectNumber buttons / other component and receiver controls Controls and displays Remote controlReceiver Multi Control buttonsComponent control buttons ADV.SURR Use to switch between the various surround modes5TUNE/ST +/- /ENTER TV Control buttonsOperating range of remote control Listening in surround sound Listening to your systemListening to your system Chapter Auto playbackListening to your system Setting the effect optionsUsing the Advanced surround effects Setting What it doesSTEREO/F.S.SURR to select Front Stage Using Stream DirectUsing Front Stage Surround Advance Listening in stereoUsing Virtual Surround Back VSB Using surround back channel processingListening with Acoustic Calibration EQ Using the Sound Retriever Using Midnight and LoudnessVirtual surround back channel option Playing other sources Using the tone controlsChoosing the input signal Listening to your system Enhancing dialogSelecting the front audio inputs Press F.AUDIO SHIFT+DVD on the remote controlPlayback the connected component Basic playback controls Using the USB interfaceUSB playback USB playback ChapterAbout MPEG-4 AAC USB playbackCompressed audio compatibility Other compatibility informationSelect the setting you want to adjust System Setup menuSystem Setup menu Chapter Surround back speaker settingManual Mcacc speaker setup System Setup menuFine Speaker Distance Select ‘Fine Ch Level’ from the Manual Mcacc setup menuSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Fine Channel LevelAcoustic Calibration EQ Setting the Acoustic Calibration EQ AutomaticallySelect ‘OK’ to copy and confirm Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Select ‘EQ Data Copy’ from the Manual Mcacc setup menuChecking your Acoustic Calibration EQ settings Manual speaker setupManual SP Setup menu Speaker SettingChannel Level Default setting 100HzSelect ‘Crossover Network’ from the Manual SP Setup menu Crossover NetworkSpeaker Distance Listening to the radio Using the tunerUsing the tuner Chapter Saving station presetsChanging the frequency step Using the tunerNaming station presets Listening to station presetsMaking recordings Chapter Making recordingsMaking an audio or a video recording Operating other Pioneer components Setting the remote to control other componentsControlling the rest of your system Controlling the rest of your system ChapterPress and hold Enter for about two seconds Erasing all of the remote control presetsUse Name from the list then press EnterControlling the rest of your system Direct function Confirming preset codesUse to switch direct function on or OFF then press Enter LCD shows OK to confirm the settingControlling the rest of your system Controls for TVs TOP Menu Controlling the rest of your systemControls for other components Disc MenuDisc RECSHIFT+ REC Stop+ CH+ HDD Shift+ CH DVD ShiftOther connections Connecting using HdmiOther connections Chapter About Hdmi Second Zone speaker B setupSwitching the speaker system Other connectionsBi-amping your front speakers Same terminal in this way Other connections Bi-wiring your speakersDVD player Satellite receiver, etc Using the SR+ mode with a Pioneer plasma displayPioneer plasma DisplayAssigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuOther Setup menu Other SettingsAssigning the Hdmi inputs Dual Mono Setup Dynamic Range Control SetupLFE Attenuator Setup Select the ‘PDP Volume Control’ setting you want SR+ Setup for Pioneer plasma displaysDigital Video Converter Setup Select ‘SR+ Setup’ from the Other Setup menuAdditional information Chapter TroubleshootingProblemRemedy Additional informationAdditional information Problem RemedySee Operating other Pioneer components on Symptom RemedyPress Setup to confirm Additional information Resetting the main unitSwitching the speaker impedance Changing the TV format settingAdditional information Specifications Miscellaneous Power cord cautionCleaning the unit AM Tuner SectionPioneer Corporation