Pioneer VSX-518 manual Additional information Chapter, Troubleshooting, Problem Remedy

Page 37

Additional information

Chapter 9:

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

•If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.

Problem

Remedy

The power does not turn on.

• Disconnect the power plug from the outlet, and insert again.

 

• Make sure there are no loose strands of speaker wire touching the

 

rear panel. This could cause the receiver to shut off automatically.

 

• If the power shuts off automatically, take the unit to your nearest

 

Pioneer authorized service center or your dealer for servicing.

 

 

No sound is output when a

• Make sure the component is connected correctly (refer to

function is selected.

Connecting up on page 8).

 

• Press MUTE on the remote control to turn muting off.

 

 

No image is output when a

• Make sure the component is connected correctly (refer to

function is selected.

Connecting up on page 8).

 

• Select the correct component (use the input select buttons).

 

 

Considerable noise in radio

• Connect the antenna (page 14) and adjust the position for best

broadcasts.

reception.

 

• Route any loose cables away from the antenna terminals and wires.

 

• Fully extend the FM wire antenna, position for best reception, and

 

secure to a wall (or connect an outdoor FM antenna).

 

• Connect an additional internal or external AM antenna (page 14).

 

• Turn off equipment causing interference or move it away from the

 

receiver (or move antennas farther away from equipment causing

 

noise).

 

 

Broadcast stations cannot be

• Connect an outdoor antenna (refer to page 14).

selected automatically.

 

 

 

No sound from surround or

• Connect the speakers properly (refer to page 15).

center speakers.

• Refer to Speaker setting on page 31 to check the speaker settings.

 

• Refer to Channel level on page 32 to check the speaker levels.

 

 

09

English Deutsch Français Italiano Nederlands Español

37

En

Page 36 Page 38
Image 37
Page 36 Page 38
Contents VSX-518 Wash hands after handling Operating Environment Ventilation CautionContents Before you start Installing the receiverBefore you start Chapter Checking what’s in the box02 5 minute guide Chapter Minute guideIntroduction to home theater Listening to Surround SoundFrançais Minute guide Using the Quick SetupConnecting up Chapter Connecting upMaking cable connections Connecting a TV and DVD player Connecting upUse a coaxial digital audio cable for the connection.1 ReceiverConnect a set of audio/video outputs on Connecting the multichannel analog outputsAbout the WMA9 Pro decoder Connecting up Connecting other audio componentsCD-R, MD, DAT, Tape recorder, etc Connecting to the front panel audio mini jack Connecting other video componentsUse a three-way component video cable Using the component video jacksComp 1 DVD Comp 2 TV Comp 3 DVR Using external antennas Connecting up Connecting antennasTo improve FM reception To improve AM receptionBare wire connections Connecting up Connecting the speakersTwist exposed wire strands together Tighten terminalSpeaker placement diagrams Hints on speaker placementFollowing illustrations show 5.1 channel speaker setups Controls and displays Chapter Controls and displaysFront panel 11 12 13Display Controls and displaysVIR.SB PRO LogicDirect Auto SurrControls and displays Remote control Setup Master Volume +Level + AV ParameterSignal SEL AccessTuner Disp ClassDirect function Operating range of remote control unitLED blinks Listening to your system Chapter Listening to your systemListening in surround sound Auto playbackPress ADV Surr repeatedly to select a listening mode Using the Advanced surround effectsListening to your system Listening in stereoUsing Stream Direct Listening to your system Using Front Stage Surround AdvanceUsing the Sound Retriever Using Virtual Surround Back Listening to your system Using Phase ControlPress Phase Phase Control to switch on phase correction Press VSB Mode front panel to selectAdjust Listening to your system Setting the AV optionsSetting Press Return to confirm and exit the menuCh1 Setting What it does OptionsListening to your system Playing other sources Choosing the input signalSelecting the multichannel analog inputs System Setup menu Chapter System Setup menuUsing the System Setup menu Manual speaker setupCrossover network System Setup menuChannel level Speaker DistanceAssigning the digital inputs Input Assign menuAssigning the component video inputs Comp 1 DVD Comp 2 TV Comp 3 DVRUsing the tuner Chapter Using the tunerTuning directly to a station Listening to the radioNaming station presets Using the tuner Saving station presetsListening to station presets Nederlands EspañolMaking recordings Chapter Making recordingsMaking an audio or a video recording Prepare the recorderProblem Remedy TroubleshootingAdditional information Additional information ChapterAdditional information Resetting the main unitLfeatt Specifications Power cord cautionSwitching the speaker impedance Amplifier sectionCleaning the unit To establish a safe level We Want You Listening For a LifetimeSe laver les mains après utilisation AvertissementMilieu de fonctionnement Précaution DE VentilationTable des matières Vérification des accessoires livrés avec l’appareil Installation du récepteurPréparatifs ChapitreGuide en 5 minutes Lancez la lecture d’un DVD et réglez le volumePrésentation de l’appareil de cinéma à domicile Écoute en son surroundUtilisation de la touche de réglage rapide Quick Setup Raccordements des câbles RaccordementsCâbles audio numériques Câbles vidéoLecteur DVD Raccordement d’un téléviseur et d’un lecteur de DVDRécepteur Ce récepteurLes récepteurs satellites et par câble, ainsi que Raccordement des sorties analogiques multicanauxLes syntoniseurs de téléviseur numérique Propos du décodeur WMA9 Pro Raccordement d’autres appareils audioCD-R, MD, DAT, magnétoscope, etc Raccordement à la mini-prise audio du panneau frontal Raccordement d’autres appareils vidéoVCR.1 Utilisez un câble vidéo en composantes trois voies Utilisation des prises femelles vidéo en composantesUtilisation des antennes externes Raccordement des antennesPour améliorer la réception FM Pour améliorer la réception AMBranchement des fils nus Raccordement des enceintes10 mm Vue d’ensemble de la configuration des enceintes Conseils d’installation des enceintesSchéma de disposition des enceintes Panneau frontal Commandes et affichagesCadran Input Selector Touches de sélection d’entréeAffichage Indicateurs Signal SelectAuto Indicateurs du Syntoniseur Mono Niveau du volume principalIndicateur d’enceinte Touche Input Select TélécommandeTouches Multi Control Permet de couper/restaurer le sonAppuyez sur ces touches pour régler le niveau des canaux Permet de régler le volume d’écoutePermet d’accéder aux options AV Affiche le menu ‘supérieur’ d’un DVDSleep Signal SEL Touches numériques et commandes pour d’autres composantsVoyant DEL de la télécommande Touches TV ControlFonction directe Portée de la télécommandeLe voyant DEL clignote Le voyant DEL s’allume en continuÉcoute de sources à l’aide de votre système Lecture en mode AutoÉcoute d’une source en son surround Utilisation des effets surround avancés Écoute en mode stéréoUtilisation de la fonction Sound Retriever Utilisation des modes Stream DirectUtilisation de la fonction Front Stage Surround Advance Appuyez sur Phase Phase Control Utilisation de la fonction Phase ControlPour activer la correction de phase Utilisation de l’effet surround arrière virtuel VSBLe paramètre sélectionné Réglage des options audiovisuelles AVRéglage Fonction Options Atténuation LFE Lecture d’autres sources Choix du signal d’entréeSélection des entrées analogiques multicanaux Utilisez les touches Multi Control Input SelectorUtilisation du menu de configuration du système Menu de configuration du systèmeRéglage manuel des enceintes Réglage des enceintesRéseau de recouvrement SP SetupNiveau des canaux Distance des enceintesAffectation des entrées numériques Menu d’affectation d’entréeAffectation des entrées de l’appareil vidéo Comp 2 TV Comp 3 DVRPour écouter la radio Utilisation du tunerAmélioration du son FM stéréo Réglage direct d’une station de radioPour nommer les stations préréglées Mémorisation de stations prérégléesPour écouter les stations préréglées Pour faire un enregistrement Sélectionnez le signal d’entrée si nécessaireFaire un enregistrement audio ou vidéo Préparez l’appareil enregistreurGuide de dépannage Information complémentaireProblème éventuel Réparation possible Réinitialisation de l’appareil principal La fonction Phase ControlYES ou Plus Valeur Lfeatt 0 ou LfeattPrécautions d’usage pour le cordon d’alimentation Permutation de l’impédance des enceintesSpécifications Section amplificateurNettoyage de l’appareil English Deutsch Français Italiano Limitedwarranty Garantie Printed Imprimé en XRE3174-C Pioneer Corporation

VSX-518 specifications

The Pioneer VSX-518 is a versatile and powerful home theater receiver that has earned a reputation for delivering exceptional audio performance and comprehensive connectivity options. As part of the renowned Pioneer lineup, the VSX-518 integrates advanced technologies that enhance the listening experience, making it a popular choice among audio enthusiasts.

One of the standout features of the VSX-518 is its multi-channel audio processing capability. With 5.1 channels of amplification, this receiver can deliver immersive surround sound, ideal for movies, music, and gaming. The unit boasts an output power of up to 100 watts per channel at 8 ohms, ensuring that it can drive a wide range of speakers with ease.

The VSX-518 supports various surround sound formats, including Dolby Digital and DTS, which allow users to experience the full spectrum of audio in their favorite films and shows. Additionally, Pioneer’s proprietary technology, called Advanced Sound Retriever, enhances compressed audio formats by restoring lost details, offering improved audio clarity and depth.

Connectivity is another strong point of the VSX-518. It is equipped with multiple HDMI inputs, allowing users to connect a variety of devices, such as Blu-ray players, gaming consoles, and streaming devices, all while maintaining high-definition audio and video quality. The receiver also includes legacy connections, such as composite and component video inputs, as well as multiple audio inputs, ensuring compatibility with older equipment.

For those who enjoy customizing their audio environment, the VSX-518 features a user-friendly interface and on-screen setup guide. The built-in automatic speaker setup system simplifies the calibration process by analyzing the acoustics of the room and adjusting the receiver settings accordingly.

Another noteworthy characteristic is the inclusion of a built-in FM/AM tuner, which allows users to enjoy their favorite radio stations without the need for external components. The unit also supports FM RDS, providing useful information about broadcasted content.

In summary, the Pioneer VSX-518 is a feature-rich home theater receiver that offers a blend of powerful audio performance, advanced technologies, and extensive connectivity options. Its ability to drive multiple speakers, support for high-definition audio formats, and user-friendly setup features make it an excellent choice for anyone looking to enhance their home entertainment system. Whether watching movies, listening to music, or gaming, the VSX-518 aims to deliver an enjoyable audio experience.
Top Page Image Contents