Peavey Ecoustic 110 Mode Select 44 and Mode LED, Preset Select Mode, Preset 1, Preset 2, Preset 3

Page 10

P F C 3 F O O T S W I T C H

The optional Ecoustic PFC 3 footswitch offers tremendous‚ hands-free control over the effects built into the Ecoustic 112 & 110. A perfect addition for the those critical performances!

Mode Select (44) and Mode LED (45)

The PFC 3 footswitch (optional) operates in two modes: EFX Select mode and Preset Select mode. Pressing the Mode Switch (44) selects between the two modes. The active mode is indicated by the Mode LED (45). Illumination of the LED indicates EFX Select Mode; non-illumination indicates Preset Select Mode. Controls and indicators perform different functions relative to the active mode.

Preset Select Mode (44)

In this mode‚ all three switches control effects presets. Their corresponding LEDs indicate which preset is active. Once desired settings are achieved utilizing the effects controls on the front panel‚ double-click one of the Preset switches (46‚ 48 or 50) to store the settings. For a detailed explanation on creating and storing presets‚ refer to the Tweak Features section on the next page.

Note: When entering the EFX select mode‚ the current preset will remain active.

Preset 1 (46)

In this mode‚ Preset 1 (46) mutes and un-mutes the signal completely. The Mute LED (47) will illuminate when the signal is muted.

Preset 2 (48)

Preset 2 (48) toggles between two effects and their respective settings. This button may be used as an on/off switch if one of the settings has no effects active. To use the Modulation LED (49) as a status indicator‚ the OFF (or lower setting) should be made with the LED dark and the ON (higher setting) made with the LED illuminated.

Preset 3 (50)

Preset 3 (50) toggles between two reverb and delay settings. As with effects settings‚ this switch may be used as an on/off switch for reverb and delay. Both functions change simultaneously when this switch is depressed.

10

Image 10
Contents Page Page Important Safety Instructions Ecoustic 112 Features Ecoustic 110 FeaturesMaster Volume Power Switch 1Tweeter Level Auxiliary Channel High EFX Adjust 10Auxiliary Channel Low InputLevel 13‚ 17‚ 26 Phase Reverse 19Ecoustic 110 4-band · Ecoustic 112 5-band EQ 12‚ 16‚ 25 Low Z Input 14IEC connector/detachable line cord 34 Ground Polarity SwitchDomestic AC Mains Cord Pre/Post EQ Switch Remote Switch Connector 35Power Amp In 36 Preamp Out 37Preset 1 Mode Select 44 and Mode LEDPreset Select Mode Preset 2Tweak Adjustment Parameters Creating and Storing a Custom PresetFreq Out Setup Ecoustic 112 Block Diagram Ecoustic 110 Block Diagram Power Amp Input Power Amplifier Section Rated PowerPower Consumption DimensionDomestic 75 W @ 60 Hz 120 VAC Export 75 W @ 50/60 Hz 230 VAC Características del Ecoustic Amplificadores acústicosInterruptor de Corriente 1 Volumen MaestroNivel del Tweeter Entrada Control de Graves AuxiliarControl de Agudos Auxiliar Control de Entrada AuxiliarEntrada de Alta Impedancia high Z 15‚ 18‚ 27 Nivel 13‚ 17‚ 26Entrada de Baja Impedancia low Z 14 Inversión de Fase 19Conectador IEC/Cable de corriente removible 34 Interruptor de polaridad de tierraCable de Corriente Domestico para USA Salida del Preamplificador 37 Conectador para Control Remoto 35Entrada de Amplificador 36 Salida de Línea Baja ImpedanciaModo de Selección de Presets Selección de Modo 44 y LED de ModoCreando y Salvando Presets Personales Iniciación del Freq Out Ecoustic Domestic 75 W @ 60 Hz 120 VAC Export 75 W @ 50/60 Hz 230 VAC Ecoustic 112 Merkmale Ecoustic 110 MerkmalePower-Schalter 1 und Microphone Channel REV/DLY 8 und EFX Adjust 10 undInstrument Channel REV/DLY 9 und Level 13‚ 17‚ 26 und Phase Reverse 19 undSelect Freq Out-Feedback-Schutzschaltung 11 und Low Z Input 14 undIEC-Stecker/abziehbares Netzkabel 34 und Ground PolarityWechselstrom-Netzkabel für die USA Preamp Out 37 und Power Amp In 36 undStecker für Fußschalter 35 und Pre/Post-EQ-SchalterMode Select 44 und Mode LED Erstellen und Speichern persönlicher Presets Einrichten des Freq Out Ecoustic Domestic 75 W @ 60 Hz 120 VAC Export 75 W @ 50/60 Hz 230 VAC Caractéristiques, Ecoustic Amplificateurs pour signaux acoustiquesContrôle le volume général de votre unité Auxiliary Channel High Select Freq Out Processeur anti-effet de Larsen 11 Ground Polarity Switch Remote Switch Connector 35 C 3 F O O T S W I T C H E a K F E a T U R E S Paramétrage du Freq Out Ecoustic Domestic 75 W @ 60 Hz 120 VAC Export 75 W @ 50/60 Hz 230 VAC Page Peavey Electronics Corporation Limited Warranty 80304944