Peavey Ecoustic 112 Remote Switch Connector 35, Power Amp In 36, Preamp Out 37, Line Out Low Z

Page 9

Remote Switch Connector (35 & 41)

This 8-pin DIN connector is provided for connection of the Ecoustic PFC 3 footswitch (optional). The footswitch cable should be connected before the amp is powered up. See the Footswitch section of this manual for explanation of switch operation.

Note: Adding the optional footswitch allows the user to store 3 presets as well as remotely mute the amplifier.

Power Amp In (36 & 43)

This 1/4" jack is used to connect a line-level signal source to the power amplifier.

Preamp Out (37 & 42)

This 1/4" jacks allows patching to mixing consoles‚ tape recorders‚ etc. Use a shielded cable to patch from this jack to the input of the device receiving the signal. This patch does not affect the operation of the amplifier or the signal continuing to the power amp and speakers.

Note: A single button‚ shielded footswitch used in the preamp out jack can be used to mute the amplifier.

Line Out: Low Z (38)

An XLR jack is provided to route the balanced signal to mixing/recording consoles.

Pre/Post EQ Switch (39)

Selects either Instrument (Pre EQ) or both the Instrument and Microphone channel (Post EQ) signals and routes to the Line Out XLR jack (38).

Note: For proper ventilation‚ allow a minimum of 12" of clearance on all sides of the unit.

9

Image 9
Contents Page Page Important Safety Instructions Ecoustic 110 Features Ecoustic 112 FeaturesPower Switch 1 Master VolumeTweeter Level Auxiliary Channel Low EFX Adjust 10Auxiliary Channel High InputEcoustic 110 4-band · Ecoustic 112 5-band EQ 12‚ 16‚ 25 Phase Reverse 19Level 13‚ 17‚ 26 Low Z Input 14Ground Polarity Switch IEC connector/detachable line cord 34Domestic AC Mains Cord Power Amp In 36 Remote Switch Connector 35Pre/Post EQ Switch Preamp Out 37Preset Select Mode Mode Select 44 and Mode LEDPreset 1 Preset 2Creating and Storing a Custom Preset Tweak Adjustment ParametersFreq Out Setup Ecoustic 112 Block Diagram Ecoustic 110 Block Diagram Power Consumption Power Amplifier Section Rated PowerPower Amp Input DimensionDomestic 75 W @ 60 Hz 120 VAC Export 75 W @ 50/60 Hz 230 VAC Amplificadores acústicos Características del EcousticVolumen Maestro Interruptor de Corriente 1Nivel del Tweeter Control de Agudos Auxiliar Control de Graves AuxiliarEntrada Control de Entrada AuxiliarEntrada de Baja Impedancia low Z 14 Nivel 13‚ 17‚ 26Entrada de Alta Impedancia high Z 15‚ 18‚ 27 Inversión de Fase 19Interruptor de polaridad de tierra Conectador IEC/Cable de corriente removible 34Cable de Corriente Domestico para USA Entrada de Amplificador 36 Conectador para Control Remoto 35Salida del Preamplificador 37 Salida de Línea Baja ImpedanciaSelección de Modo 44 y LED de Modo Modo de Selección de PresetsCreando y Salvando Presets Personales Iniciación del Freq Out Ecoustic Domestic 75 W @ 60 Hz 120 VAC Export 75 W @ 50/60 Hz 230 VAC Ecoustic 110 Merkmale Ecoustic 112 MerkmalePower-Schalter 1 und EFX Adjust 10 und Microphone Channel REV/DLY 8 undInstrument Channel REV/DLY 9 und Select Freq Out-Feedback-Schutzschaltung 11 und Phase Reverse 19 undLevel 13‚ 17‚ 26 und Low Z Input 14 undGround Polarity IEC-Stecker/abziehbares Netzkabel 34 undWechselstrom-Netzkabel für die USA Stecker für Fußschalter 35 und Power Amp In 36 undPreamp Out 37 und Pre/Post-EQ-SchalterMode Select 44 und Mode LED Erstellen und Speichern persönlicher Presets Einrichten des Freq Out Ecoustic Domestic 75 W @ 60 Hz 120 VAC Export 75 W @ 50/60 Hz 230 VAC Amplificateurs pour signaux acoustiques Caractéristiques, EcousticContrôle le volume général de votre unité Auxiliary Channel High Select Freq Out Processeur anti-effet de Larsen 11 Ground Polarity Switch Remote Switch Connector 35 C 3 F O O T S W I T C H E a K F E a T U R E S Paramétrage du Freq Out Ecoustic Domestic 75 W @ 60 Hz 120 VAC Export 75 W @ 50/60 Hz 230 VAC Page Peavey Electronics Corporation Limited Warranty 80304944