dbx Pro QUANTUM user manual Important Safety Instructions

Page 2

IMPORTANT SAFETY INSTRUCTIONS

C A U T I O N

RISK OF ELECTRIC SHOCK

DO NOT OPEN

A T T E N T I O N : RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

W A R N I N G : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE

The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner’s manual.

These symbols warn that there are no user serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer’s warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off immediately and take it to a dealer for service. Disconnect the unit during storms to prevent damage.

SAFETY INSTRUCTIONS

NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A POWER CORD.

WARNING: THIS APPLIANCE MUST BE EARTHED.

The cores in the mains lead are coloured in accordance with the following code:

GREEN and YELLOW - Earth

BLUE - Neutral

BROWN - Live

As colours of the cores in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The core which is coloured green and yellow must be connected to the ter- minal in the plug marked with the letter E, or with the earth symbol, or coloured green, or green and yellow.

The core which is coloured blue must be connected to the terminal marked N or coloured black.

The core which is coloured brown must be connected to the terminal marked L or coloured red.

This equipment may require the use of a different line cord, attachment plug, or both, depending on the available power source at installation. If the attachment plug needs to be changed, refer servicing to qualified service personnel who should refer to the table below. The green/yellow wire shall be connected direct- ly to the units chassis.

CONDUCTOR

WIRE COLOR

Normal

Alt

 

 

 

 

 

 

L

LIVE

BROWN

BLACK

 

 

 

 

N

NEUTRAL

BLUE

WHITE

 

 

 

 

E

EARTH GND

GREEN/YEL

GREEN

WARNING: If the ground is defeated, certain fault conditions in the unit or in the system to which it is connected can result in full line voltage between chassis and earth ground. Severe injury or death can then result if the chassis and earth ground are touched simultaneously.

WARNING FOR YOUR PROTECTION PLEASE READ THE FOLLOWING:

KEEP THESE INSTRUCTIONS

HEED ALL WARNINGS

FOLLOW ALL INSTRUCTIONS

CLEAN ONLY WITH A DAMP CLOTH.

DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURERS INSTRUCTIONS.

DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES; OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.

ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MAN- UFACTURER.

UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.

WATER AND MOISTURE: Appliance should not be used near water (e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.

POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

SERVICING: To reduce the risk of fire or electric shock, the user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE: Replace fuse with same type and rating only.

MULTIPLE-INPUT VOLTAGE: This equipment may require the use of a different line cord, attachment plug, or both, depending on the available power source at installation. Connect this equipment only to the power source indicated on the equipment rear panel. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel or equivalent.

Image 2
Contents Quantum Important Safety Instructions Declaration Conformity Table of Contents QuantumFigure Index Page Intro What is QUANTUM? IntroductionWarranty Introduction What is QUANTUM?Service Contact Info Quantum Section Front Panel Getting StartedRear Panel Connections Getting Started Section Front Panel Signal Path Quantum WizardQuantum is a Mastering Processor that has many features Getting Started Section Mastering and the QuantumQuantum Navigation Navigation Multiband CompressorNavigating the Broadband Compressor Navigation Section Broadband CompressorNavigating the Multiband Gate Multiband GateNavigating the Broadband Gate Navigation Section Broadband GateNavigating the Multiband Limiter Multiband LimiterNavigating theBroadband Limiter Navigation Section Broadband LimiterNavigating the Multiband EQ/XOver EQ/XOverNavigating the Broadband EQ/SEQ Navigation Section EQ/SEQNavigating Norm/Output Norm/OutputNavigating Other Navigation Section OtherNavigating Utility UtilitySection Software Operations FX ChainsSoftware Operations Section FX Chains Chain Type Stereo BroadbandChain Type Mono Mono Input CH1 or CH2Software Operations Section Programs/Setups Program Pop MasterSaving a Setup SectionReplace Old Software Operations Section Saving a SetupSaving a Program Store NewAnalog Meters Bypass FunctionMeters TSE Level MetersMeter Options Software Operations Section MetersDigital Meters CompressorGate / Expander Monitor OutputsLimiter De-EsserDetailed Detailed Parameters Multiband CompressionDetailed Parameters Section Multiband Compression Broadband Compression Detailed Parameters Section Broadband Compression Release 360 to 5 dB / Sec per band or global Ratio 11.0 to 115 per band or globalAttack 0.1 to 200 m Sec per band or global Max ATT 0 to Inf. dB per band or globalDetailed Parameters Section Broadband Gate Multiband LimitingLimiter On/Off Broadband LimitingAttack .01 to 200 m Sec per band or global Type PkStop+/RMSPOS Pre/Post Detailed Parameters Section Broadband LimitingEQ On/Off Type Const Q / Adapt QXOver SEQ1 FC 20.0 Hz to 20.0 kHz Detailed Parameters Section SEQSchain EQ On/Off SEQ2, 3, 4 FC 20.0 Hz to 20.0 kHzStereo Adjust TypeDe-Esser Detailed Parameters Section Ambience13 TCM Normalization OutputDither Out All or Digital Detailed Parameters Section OutputShaping S1 or S2 Page Utilities Utilities Input OutputMidi CC Map Utilities Section OutputDigital Input Controls Midi Program Changes Setup Sysex DataMidi Channels Sysex DumpMisc Utilities Section Setup Sysex DataA/D Calibrate Page Guide Hardware Application GuideAnalog Mastering SoftwareApplication Guide Section Digital Mastering DAW to DAT Application Guide Section Analog Tracking 586Digital Tracking Application Guide Section Analog Mixing Digital Mixing Application Guide Section Analog to Digital Converter Sample Rate Converter QUANTUMAppendix Appendix a Miscellaneous Information Hard & Soft ResetsChange Default Startup Program Front Panel LockoutBy Roger Johnson TypeIV White Paper Appendix BAppendix B TypeIV White Paper Converted Level vs. Input LevelType Amplitude Time Clip Level High-Frequency Information Completely Lost Appendix C Midi Clock Info Clock ModesQuantum Sync Input Fig. C.1Appendix C Miscellaneous Clock Info Fig. C.2Receive One Setup 43h ProceduresRequest One Setup 02h Sysex Definitions Appendix DAppendix D Sysex Definitions Procedure Setup Dump Version Reset Device 21hSysex Setup Dump Sample Setup Type and Setup NumberAppendix E Midi CC Tables Midi CC MultiBand ChainsMidi CC Tables Appendix E Midi CC MultiBand Chains Midi CC Stereo Non-MultiBandMidi CC Dual Mono Chains Midi CC Stereo Non-MultibandMidi CC Tables Appendix E Midi CC Dual Mono Chains Appendix F Factory Presets Factory ProgramsMono Factory SetupsStereo Appendix G Specifications SpecificationsAppendix H Appendix H Quantum Harman International Company