dbx Pro QUANTUM user manual Monitor Outputs, Limiter, Gate / Expander, De-Esser

Page 38

Section 3 Software Operations

QUANTUM

3.6 Meters (cont.)

Limiter

The limiter’s threshold meter works on the same principle. When the signal is under the thresh- old setting, the signal is not being processed by the limiter section. The next part of the thresh- old meter is the “o”. It represents the OverEasy® range of compression. When the signal exceeds the threshold set in the limiter section, the plus (+) sign will darken, and gain reduc- tion will begin to occur as a result of the signal exceeding the limiter’s threshold.

Gate / Expander

When the signal is under the threshold set in the gate section, the gate is “closed”, or signal is being attenuated. When the signal is under the threshold, the minus (-) sign is darkened, and when the signal passes over the threshold, the plus (+) sign is darkened.

De-Esser

The De-esser also has a threshold meter. The threshold meter for this element is also dis- played in the upper left corner. When the plus sign is darkened, the threshold has been exceeded and De-Essing is being applied to the signal.

3.7 Monitor Outputs

Monitoring separate bands is a useful and easily accomplished function in the QUANTUM. By pressing the METER/MONITOR button twice you are able to access the monitor selection page. Use the DATA WHEEL to select at which point you would like to monitor. The headphone graphic and arrow change to show the point in the signal chain you are monitoring. The text under “Monitor Out” shows which band and position you are currently selecting. This is a very important option. As you are adjusting dynamic processing within individual bands it helps to monitor the changes made to those bands. “Band 1 pre” monitor position is located just after the crossover, before the gate, compressor, and limiter. “Band 1 post” is located after the gate, compressor, and limiter, before the Normalizer and output. The other bands (2-4) oper- ate in the same fashion.

®

28

QUANTUM User Manual

 

 

Image 38
Contents Quantum Important Safety Instructions Declaration Conformity Table of Contents QuantumFigure Index Page Intro What is QUANTUM? IntroductionWarranty Introduction What is QUANTUM?Service Contact Info Quantum Section Front Panel Getting StartedRear Panel Connections Getting Started Section Front Panel Signal Path Quantum WizardQuantum is a Mastering Processor that has many features Getting Started Section Mastering and the QuantumQuantum Navigation Navigation Multiband CompressorNavigating the Broadband Compressor Navigation Section Broadband CompressorNavigating the Multiband Gate Multiband GateNavigating the Broadband Gate Navigation Section Broadband GateNavigating the Multiband Limiter Multiband LimiterNavigating theBroadband Limiter Navigation Section Broadband LimiterNavigating the Multiband EQ/XOver EQ/XOverNavigating the Broadband EQ/SEQ Navigation Section EQ/SEQNavigating Norm/Output Norm/OutputNavigating Other Navigation Section OtherNavigating Utility UtilitySection Software Operations FX ChainsSoftware Operations Section FX Chains Chain Type Stereo BroadbandChain Type Mono Mono Input CH1 or CH2Software Operations Section Programs/Setups Program Pop MasterSaving a Setup SectionReplace Old Software Operations Section Saving a SetupSaving a Program Store NewAnalog Meters Bypass FunctionMeters TSE Level MetersMeter Options Software Operations Section MetersDigital Meters CompressorGate / Expander Monitor OutputsLimiter De-EsserDetailed Detailed Parameters Multiband CompressionDetailed Parameters Section Multiband Compression Broadband Compression Detailed Parameters Section Broadband Compression Release 360 to 5 dB / Sec per band or global Ratio 11.0 to 115 per band or globalAttack 0.1 to 200 m Sec per band or global Max ATT 0 to Inf. dB per band or globalDetailed Parameters Section Broadband Gate Multiband LimitingLimiter On/Off Broadband LimitingAttack .01 to 200 m Sec per band or global Type PkStop+/RMSPOS Pre/Post Detailed Parameters Section Broadband LimitingEQ On/Off Type Const Q / Adapt QXOver SEQ1 FC 20.0 Hz to 20.0 kHz Detailed Parameters Section SEQSchain EQ On/Off SEQ2, 3, 4 FC 20.0 Hz to 20.0 kHzStereo Adjust TypeDe-Esser Detailed Parameters Section Ambience13 TCM Normalization OutputDither Out All or Digital Detailed Parameters Section OutputShaping S1 or S2 Page Utilities Utilities Input OutputMidi CC Map Utilities Section OutputDigital Input Controls Midi Program Changes Setup Sysex DataMidi Channels Sysex DumpMisc Utilities Section Setup Sysex DataA/D Calibrate Page Guide Hardware Application GuideAnalog Mastering SoftwareApplication Guide Section Digital Mastering DAW to DAT Application Guide Section Analog Tracking 586Digital Tracking Application Guide Section Analog Mixing Digital Mixing Application Guide Section Analog to Digital Converter Sample Rate Converter QUANTUMAppendix Appendix a Miscellaneous Information Hard & Soft ResetsChange Default Startup Program Front Panel LockoutBy Roger Johnson TypeIV White Paper Appendix BAppendix B TypeIV White Paper Converted Level vs. Input LevelType Amplitude Time Clip Level High-Frequency Information Completely Lost Appendix C Midi Clock Info Clock ModesQuantum Sync Input Fig. C.1Appendix C Miscellaneous Clock Info Fig. C.2Receive One Setup 43h ProceduresRequest One Setup 02h Sysex Definitions Appendix DAppendix D Sysex Definitions Procedure Setup Dump Version Reset Device 21hSysex Setup Dump Sample Setup Type and Setup NumberAppendix E Midi CC Tables Midi CC MultiBand ChainsMidi CC Tables Appendix E Midi CC MultiBand Chains Midi CC Stereo Non-MultiBandMidi CC Dual Mono Chains Midi CC Stereo Non-MultibandMidi CC Tables Appendix E Midi CC Dual Mono Chains Appendix F Factory Presets Factory ProgramsMono Factory SetupsStereo Appendix G Specifications SpecificationsAppendix H Appendix H Quantum Harman International Company