dbx Pro QUANTUM Detailed Parameters Section SEQ, Schain EQ On/Off, SEQ1 FC 20.0 Hz to 20.0 kHz

Page 49

QUANTUM

Detailed Parameters Section 4

4.9 SEQ

When in the broadband mode, not only do you have access to the equalizer but also another EQ in the sidechain. Having EQ in the sidechain lets you boost or cut various frequencies prior to the dynamics processor detector. Cutting low-end in the sidechain will mean the detection circuit will see less low-end, thus the signal will be compressed based on it's high frequency content.º

Sidechain

EQ

Detection

Circuit

Input

Processing

Output

Fig. 4.3

.

Within the SEQ menu on the QUANTUM the following parameters are user adjustable: Press the EQ/XOVER button twice when in non-multiband mode to access the SEQ.

Schain EQ On/Off

This control turns all 5 bands on/off.

Type Const Q / Adapt Q

This controls all 5 bands. All bands must use the same Q type.

SEQ1 FC 20.0 Hz to 20.0 kHz

This controls the corner frequency for the low frequency shelving EQ band.

Slope 3 to 12 dB / Octave

Sets the slope of the shelf.

Level -12 to + 12 dB

Amount of boost or cut. Adjustable in 1/2 dB steps.

SEQ2, 3, 4 FC 20.0 Hz to 20.0 kHz

This controls the center point for the parametric EQ.

Q 0.25 to 16.0

Sets the width of the boost / cut.

Level -12 to + 12 dB

Amount of boost or cut. Adjustable in 1/2 dB steps.

SEQ5 FC 20.0 Hz to 20.0 kHz

This controls the corner frequency for the high frequency shelving EQ band.

®

QUANTUM User Manual	39

Image 49

Contents Quantum Important Safety Instructions Declaration Conformity Quantum Table of ContentsFigure Index Page Intro Introduction What is QUANTUM?Service Contact Info Introduction What is QUANTUM?Warranty Quantum Section Rear Panel Connections Getting StartedFront Panel Getting Started Section Front Panel Quantum Wizard Signal PathGetting Started Section Mastering and the Quantum Quantum is a Mastering Processor that has many featuresQuantum Navigation Multiband Compressor NavigationNavigation Section Broadband Compressor Navigating the Broadband CompressorMultiband Gate Navigating the Multiband GateNavigation Section Broadband Gate Navigating the Broadband GateMultiband Limiter Navigating the Multiband LimiterNavigation Section Broadband Limiter Navigating theBroadband LimiterEQ/XOver Navigating the Multiband EQ/XOverNavigation Section EQ/SEQ Navigating the Broadband EQ/SEQNorm/Output Navigating Norm/OutputNavigation Section Other Navigating OtherUtility Navigating UtilitySection FX Chains Software OperationsChain Type Stereo Broadband Software Operations Section FX ChainsMono Input CH1 or CH2 Chain Type MonoProgram Pop Master Software Operations Section Programs/SetupsSection Saving a SetupSaving a Program Software Operations Section Saving a SetupReplace Old Store NewMeters Bypass FunctionAnalog Meters TSE Level MetersDigital Meters Software Operations Section MetersMeter Options CompressorLimiter Monitor OutputsGate / Expander De-EsserDetailed Multiband Compression Detailed ParametersDetailed Parameters Section Multiband Compression Broadband Compression Detailed Parameters Section Broadband Compression Attack 0.1 to 200 m Sec per band or global Ratio 11.0 to 115 per band or globalRelease 360 to 5 dB / Sec per band or global Max ATT 0 to Inf. dB per band or globalMultiband Limiting Detailed Parameters Section Broadband GateAttack .01 to 200 m Sec per band or global Broadband LimitingLimiter On/Off Type PkStop+/RMSEQ On/Off Detailed Parameters Section Broadband LimitingPOS Pre/Post Type Const Q / Adapt QXOver Schain EQ On/Off Detailed Parameters Section SEQSEQ1 FC 20.0 Hz to 20.0 kHz SEQ2, 3, 4 FC 20.0 Hz to 20.0 kHzType Stereo Adjust13 TCM Detailed Parameters Section AmbienceDe-Esser Output NormalizationShaping S1 or S2 Detailed Parameters Section OutputDither Out All or Digital Page Utilities Input Output UtilitiesDigital Input Controls Utilities Section OutputMidi CC Map Midi Channels Setup Sysex DataMidi Program Changes Sysex DumpA/D Calibrate Utilities Section Setup Sysex DataMisc Page Guide Analog Mastering Application GuideHardware SoftwareApplication Guide Section Digital Mastering DAW to DAT 586 Application Guide Section Analog TrackingDigital Tracking Application Guide Section Analog Mixing Digital Mixing Application Guide Section Analog to Digital Converter Sample Rate Converter QUANTUMAppendix Change Default Startup Program Hard & Soft ResetsAppendix a Miscellaneous Information Front Panel LockoutTypeIV White Paper Appendix B By Roger JohnsonConverted Level vs. Input Level Appendix B TypeIV White PaperType Amplitude Time Clip Level High-Frequency Information Completely Lost Clock Modes Appendix C Midi Clock InfoFig. C.1 Quantum Sync InputFig. C.2 Appendix C Miscellaneous Clock InfoRequest One Setup 02h ProceduresReceive One Setup 43h Sysex Definitions Appendix DAppendix D Sysex Definitions Sysex Setup Dump Sample Reset Device 21hProcedure Setup Dump Version Setup Type and Setup NumberMidi CC MultiBand Chains Appendix E Midi CC TablesMidi CC Stereo Non-MultiBand Midi CC Tables Appendix E Midi CC MultiBand ChainsMidi CC Stereo Non-Multiband Midi CC Dual Mono ChainsMidi CC Tables Appendix E Midi CC Dual Mono Chains Factory Programs Appendix F Factory PresetsStereo Factory SetupsMono Specifications Appendix G SpecificationsAppendix H Appendix H Quantum Harman International Company