dbx Pro QUANTUM user manual Utilities Section Setup Sysex Data, A/D Calibrate, Misc

Page 59

QUANTUM

Utilities Section 5

5.8 Setup SYSEX Data (cont.)

1.Enter the “Utility” menu by pressing the UTILITY button once.

2.Press NEXT PAGE button until page 8 is reached.

3.Use the DATA WHEEL to select which setup you would like to dump.

4.Press the DATA WHEEL to change the cursor location to the next selection.

5Select the name of the preset you would like to dump.

6.Press the UTILITY button to start the dump.

5.9 A/D Calibrate

A/D CALIBRATE

This page of “Utilities” is a calibration section for the analog to digital converter chips. To cal- ibrate the converters, first turn the input controls of the QUANTUM fully counter-clockwise (-∞). Calibrations performed with these controls open at all could result in inaccurate calibra- tions, giving the QUANTUM poor processing performance. After the input controls have been turned to the (-∞) position, press the UTILITY button. If the calibration is not successful, the following text will appear in the third parameter area: “A/D CAL FAIL!” If this happens you should turn the QUANTUM off then back on. If the problem persists, call dbx technical support at 1-801-568-7660 for assistance. Call after the unit is allowed to warm up to operating temper- ature (approx. 10 minutes).

5.10 Misc.

CONTRAST

The contrast selection adjusts the displays visibility.

®

QUANTUM User Manual	49

Image 59

Contents Quantum Important Safety Instructions Declaration Conformity Quantum Table of ContentsFigure Index Page Intro Introduction What is QUANTUM?Warranty Introduction What is QUANTUM?Service Contact Info Quantum Section Front Panel Getting StartedRear Panel Connections Getting Started Section Front Panel Quantum Wizard Signal PathGetting Started Section Mastering and the Quantum Quantum is a Mastering Processor that has many featuresQuantum Navigation Multiband Compressor NavigationNavigation Section Broadband Compressor Navigating the Broadband CompressorMultiband Gate Navigating the Multiband GateNavigation Section Broadband Gate Navigating the Broadband GateMultiband Limiter Navigating the Multiband LimiterNavigation Section Broadband Limiter Navigating theBroadband LimiterEQ/XOver Navigating the Multiband EQ/XOverNavigation Section EQ/SEQ Navigating the Broadband EQ/SEQNorm/Output Navigating Norm/OutputNavigation Section Other Navigating OtherUtility Navigating UtilitySection FX Chains Software OperationsChain Type Stereo Broadband Software Operations Section FX ChainsMono Input CH1 or CH2 Chain Type MonoProgram Pop Master Software Operations Section Programs/SetupsSection Saving a SetupStore New Software Operations Section Saving a SetupSaving a Program Replace OldTSE Level Meters Bypass FunctionMeters Analog MetersCompressor Software Operations Section MetersDigital Meters Meter OptionsDe-Esser Monitor OutputsLimiter Gate / ExpanderDetailed Multiband Compression Detailed ParametersDetailed Parameters Section Multiband Compression Broadband Compression Detailed Parameters Section Broadband Compression Max ATT 0 to Inf. dB per band or global Ratio 11.0 to 115 per band or globalAttack 0.1 to 200 m Sec per band or global Release 360 to 5 dB / Sec per band or globalMultiband Limiting Detailed Parameters Section Broadband GateType PkStop+/RMS Broadband LimitingAttack .01 to 200 m Sec per band or global Limiter On/OffType Const Q / Adapt Q Detailed Parameters Section Broadband LimitingEQ On/Off POS Pre/PostXOver SEQ2, 3, 4 FC 20.0 Hz to 20.0 kHz Detailed Parameters Section SEQSchain EQ On/Off SEQ1 FC 20.0 Hz to 20.0 kHzType Stereo AdjustDe-Esser Detailed Parameters Section Ambience13 TCM Output NormalizationDither Out All or Digital Detailed Parameters Section OutputShaping S1 or S2 Page Utilities Input Output UtilitiesMidi CC Map Utilities Section OutputDigital Input Controls Sysex Dump Setup Sysex DataMidi Channels Midi Program ChangesMisc Utilities Section Setup Sysex DataA/D Calibrate Page Guide Software Application GuideAnalog Mastering HardwareApplication Guide Section Digital Mastering DAW to DAT 586 Application Guide Section Analog TrackingDigital Tracking Application Guide Section Analog Mixing Digital Mixing Application Guide Section Analog to Digital Converter Sample Rate Converter QUANTUMAppendix Front Panel Lockout Hard & Soft ResetsChange Default Startup Program Appendix a Miscellaneous InformationTypeIV White Paper Appendix B By Roger JohnsonConverted Level vs. Input Level Appendix B TypeIV White PaperType Amplitude Time Clip Level High-Frequency Information Completely Lost Clock Modes Appendix C Midi Clock InfoFig. C.1 Quantum Sync InputFig. C.2 Appendix C Miscellaneous Clock InfoSysex Definitions Appendix D ProceduresRequest One Setup 02h Receive One Setup 43hAppendix D Sysex Definitions Setup Type and Setup Number Reset Device 21hSysex Setup Dump Sample Procedure Setup Dump VersionMidi CC MultiBand Chains Appendix E Midi CC TablesMidi CC Stereo Non-MultiBand Midi CC Tables Appendix E Midi CC MultiBand ChainsMidi CC Stereo Non-Multiband Midi CC Dual Mono ChainsMidi CC Tables Appendix E Midi CC Dual Mono Chains Factory Programs Appendix F Factory PresetsMono Factory SetupsStereo Specifications Appendix G SpecificationsAppendix H Appendix H Quantum Harman International Company