dbx Pro QUANTUM user manual Appendix D Sysex Definitions

Page 82

Appendix D SYSEX Definitions

QUANTUM

yyThe Setup number, 1-100 (00-63h)

zzByte Count

dd(n)

Program data

The Receive One Setup procedure is used to load a Setup into the QUANTUM. The number of setup bytes to be received

(n)is different for each setup. If the QUANTUM is sent a Receive One setup procedure where the setup number is not a valid RAM destination, it will be ignored.

Request Bulk Dump (49h)

SYS_HEAD, 49(h), F7(h)

When a Request Bulk Dump procedure is received, the QUANTUM will respond with a Receive Bulk Dump proce- dure.

Receive Bulk Dump (48h)

SYS_HEAD 48(h), dd(1st)1 dd(1st)2, ... dd(nth)1, dd(nth)2, F7(h)

dd(n)

Bulk Dump Data

The Receive Bulk Dump procedure is used to load all User Programs into the QUANTUM. A software version num- ber is imbedded in the data.

Receive Key Scan Code (54h)

SYS_HEAD, 54(h), cc, F7(h)

cc Code for the Key Scan (note: there is only one byte, not two)

The Receive Key Scan Code procedure is used to emulate a button press on the front panel of the QUANTUM. See the Key Scan Code Maps for a list of Key Scan codes. The device will respond with a Receive Key Accepted pro- cedure.

*Encoder controls are included, to allow you to emulate encoder moves as well as button presses.

**Config is included to make it accessible through SYSEX commands even though it is not represented by its own button.

Receive Key Accepted (56h)

SYS_HEAD, 56(h), cc1, cc2, F7(h)

cc Code echoed for the Key Scan received. (00(h) if key is invalid)

The Receive Key Accepted procedure is sent from the QUANTUM in response and acceptance of a Receive Scan Code Key or Receive Hold Scan Code Key procedure but is ignored if received by the QUANTUM.

Reset Program (20h)

SYS_HEAD, 20(h), F7(h)

®

72	QUANTUM User Manual

Image 82

Contents Quantum Important Safety Instructions Declaration Conformity Table of Contents QuantumFigure Index Page Intro What is QUANTUM? IntroductionService Contact Info Introduction What is QUANTUM?Warranty Quantum Section Rear Panel Connections Getting StartedFront Panel Getting Started Section Front Panel Signal Path Quantum WizardQuantum is a Mastering Processor that has many features Getting Started Section Mastering and the QuantumQuantum Navigation Navigation Multiband CompressorNavigating the Broadband Compressor Navigation Section Broadband CompressorNavigating the Multiband Gate Multiband GateNavigating the Broadband Gate Navigation Section Broadband GateNavigating the Multiband Limiter Multiband LimiterNavigating theBroadband Limiter Navigation Section Broadband LimiterNavigating the Multiband EQ/XOver EQ/XOverNavigating the Broadband EQ/SEQ Navigation Section EQ/SEQNavigating Norm/Output Norm/OutputNavigating Other Navigation Section OtherNavigating Utility UtilitySection Software Operations FX ChainsSoftware Operations Section FX Chains Chain Type Stereo BroadbandChain Type Mono Mono Input CH1 or CH2Software Operations Section Programs/Setups Program Pop MasterSaving a Setup SectionReplace Old Software Operations Section Saving a SetupSaving a Program Store NewAnalog Meters Bypass FunctionMeters TSE Level MetersMeter Options Software Operations Section MetersDigital Meters CompressorGate / Expander Monitor OutputsLimiter De-EsserDetailed Detailed Parameters Multiband CompressionDetailed Parameters Section Multiband Compression Broadband Compression Detailed Parameters Section Broadband Compression Release 360 to 5 dB / Sec per band or global Ratio 11.0 to 115 per band or globalAttack 0.1 to 200 m Sec per band or global Max ATT 0 to Inf. dB per band or globalDetailed Parameters Section Broadband Gate Multiband LimitingLimiter On/Off Broadband LimitingAttack .01 to 200 m Sec per band or global Type PkStop+/RMSPOS Pre/Post Detailed Parameters Section Broadband LimitingEQ On/Off Type Const Q / Adapt QXOver SEQ1 FC 20.0 Hz to 20.0 kHz Detailed Parameters Section SEQSchain EQ On/Off SEQ2, 3, 4 FC 20.0 Hz to 20.0 kHzStereo Adjust Type13 TCM Detailed Parameters Section AmbienceDe-Esser Normalization OutputShaping S1 or S2 Detailed Parameters Section OutputDither Out All or Digital Page Utilities Utilities Input OutputDigital Input Controls Utilities Section OutputMidi CC Map Midi Program Changes Setup Sysex DataMidi Channels Sysex DumpA/D Calibrate Utilities Section Setup Sysex DataMisc Page Guide Hardware Application GuideAnalog Mastering SoftwareApplication Guide Section Digital Mastering DAW to DAT Application Guide Section Analog Tracking 586Digital Tracking Application Guide Section Analog Mixing Digital Mixing Application Guide Section Analog to Digital Converter Sample Rate Converter QUANTUMAppendix Appendix a Miscellaneous Information Hard & Soft ResetsChange Default Startup Program Front Panel LockoutBy Roger Johnson TypeIV White Paper Appendix BAppendix B TypeIV White Paper Converted Level vs. Input LevelType Amplitude Time Clip Level High-Frequency Information Completely Lost Appendix C Midi Clock Info Clock Modes Quantum Sync Input Fig. C.1Appendix C Miscellaneous Clock Info Fig. C.2Receive One Setup 43h ProceduresRequest One Setup 02h Sysex Definitions Appendix DAppendix D Sysex Definitions Procedure Setup Dump Version Reset Device 21hSysex Setup Dump Sample Setup Type and Setup NumberAppendix E Midi CC Tables Midi CC MultiBand ChainsMidi CC Tables Appendix E Midi CC MultiBand Chains Midi CC Stereo Non-MultiBandMidi CC Dual Mono Chains Midi CC Stereo Non-MultibandMidi CC Tables Appendix E Midi CC Dual Mono Chains Appendix F Factory Presets Factory ProgramsStereo Factory SetupsMono Appendix G Specifications SpecificationsAppendix H Appendix H Quantum Harman International Company