dbx Pro QUANTUM user manual Appendix C Miscellaneous Clock Info, Fig. C.2

Page 80

Appendix C Miscellaneous Clock Info

QUANTUM

C.2 QUANTUM Sync Input (cont.)

not allow the user to change the termination setting. These pieces of equipment are usually provided with a permanent termination. If you use QUANTUM with another piece of terminated equipment in a tapped configuration, you should unterminate QUANTUM’s sync input. The same is true if you wish to use several QUANTUMs in a tapped configuration. QUANTUM can also be used in a daisy chain fashion. In a daisy chain configuration, each piece of equipment can remain terminated (and should if you are using a SuperClock) and so the termination can remain in the default position.

Whatever configuration you choose, always use high-quality 75 ohm coaxial cable for your sync connections. In addi- tion, keep the cable runs as short as possible. The preceding is especially true when using SuperClock because the fre- quencies are much higher. Failure to follow these guidelines could cause decreased audio performance and/or syn- chronization problems.

Daisy Chain Configuration

Sync Source

A

Quantum

C

Tapped Configuration

Sync Source

A

Quantum

C

Fig. C.2

®

70	QUANTUM User Manual

Image 80

Contents Quantum Important Safety Instructions Declaration Conformity Table of Contents QuantumFigure Index Page Intro What is QUANTUM? IntroductionWarranty Introduction What is QUANTUM?Service Contact Info Quantum Section Front Panel Getting StartedRear Panel Connections Getting Started Section Front Panel Signal Path Quantum WizardQuantum is a Mastering Processor that has many features Getting Started Section Mastering and the QuantumQuantum Navigation Navigation Multiband CompressorNavigating the Broadband Compressor Navigation Section Broadband CompressorNavigating the Multiband Gate Multiband GateNavigating the Broadband Gate Navigation Section Broadband GateNavigating the Multiband Limiter Multiband LimiterNavigating theBroadband Limiter Navigation Section Broadband LimiterNavigating the Multiband EQ/XOver EQ/XOverNavigating the Broadband EQ/SEQ Navigation Section EQ/SEQNavigating Norm/Output Norm/OutputNavigating Other Navigation Section OtherNavigating Utility UtilitySection Software Operations FX ChainsSoftware Operations Section FX Chains Chain Type Stereo BroadbandChain Type Mono Mono Input CH1 or CH2Software Operations Section Programs/Setups Program Pop MasterSaving a Setup SectionSoftware Operations Section Saving a Setup Saving a ProgramReplace Old Store NewBypass Function MetersAnalog Meters TSE Level MetersSoftware Operations Section Meters Digital MetersMeter Options CompressorMonitor Outputs LimiterGate / Expander De-EsserDetailed Detailed Parameters Multiband CompressionDetailed Parameters Section Multiband Compression Broadband Compression Detailed Parameters Section Broadband Compression Ratio 11.0 to 115 per band or global Attack 0.1 to 200 m Sec per band or globalRelease 360 to 5 dB / Sec per band or global Max ATT 0 to Inf. dB per band or globalDetailed Parameters Section Broadband Gate Multiband LimitingBroadband Limiting Attack .01 to 200 m Sec per band or globalLimiter On/Off Type PkStop+/RMSDetailed Parameters Section Broadband Limiting EQ On/OffPOS Pre/Post Type Const Q / Adapt QXOver Detailed Parameters Section SEQ Schain EQ On/OffSEQ1 FC 20.0 Hz to 20.0 kHz SEQ2, 3, 4 FC 20.0 Hz to 20.0 kHzStereo Adjust TypeDe-Esser Detailed Parameters Section Ambience13 TCM Normalization OutputDither Out All or Digital Detailed Parameters Section OutputShaping S1 or S2 Page Utilities Utilities Input OutputMidi CC Map Utilities Section OutputDigital Input Controls Setup Sysex Data Midi ChannelsMidi Program Changes Sysex DumpMisc Utilities Section Setup Sysex DataA/D Calibrate Page Guide Application Guide Analog MasteringHardware SoftwareApplication Guide Section Digital Mastering DAW to DAT Application Guide Section Analog Tracking 586Digital Tracking Application Guide Section Analog Mixing Digital Mixing Application Guide Section Analog to Digital Converter Sample Rate Converter QUANTUMAppendix Hard & Soft Resets Change Default Startup ProgramAppendix a Miscellaneous Information Front Panel LockoutBy Roger Johnson TypeIV White Paper Appendix BAppendix B TypeIV White Paper Converted Level vs. Input LevelType Amplitude Time Clip Level High-Frequency Information Completely Lost Appendix C Midi Clock Info Clock ModesQuantum Sync Input Fig. C.1Appendix C Miscellaneous Clock Info Fig. C.2Procedures Request One Setup 02hReceive One Setup 43h Sysex Definitions Appendix DAppendix D Sysex Definitions Reset Device 21h Sysex Setup Dump SampleProcedure Setup Dump Version Setup Type and Setup NumberAppendix E Midi CC Tables Midi CC MultiBand ChainsMidi CC Tables Appendix E Midi CC MultiBand Chains Midi CC Stereo Non-MultiBandMidi CC Dual Mono Chains Midi CC Stereo Non-MultibandMidi CC Tables Appendix E Midi CC Dual Mono Chains Appendix F Factory Presets Factory ProgramsMono Factory SetupsStereo Appendix G Specifications SpecificationsAppendix H Appendix H Quantum Harman International Company