Akai EWI5000 manual

Page 10

9.Grounding Plate: Always touch these plates while playing.

10.Octave Rollers: Move your thumb up or down over these rollers to shift the note keys' range. You can shift them up to four octaves higher or up to two octaves lower. Always touch these octave rollers while playing.

11.Glide Plate: Touch this plate while playing a note to produce a "glide" effect, which smoothly and continuously slides the pitch up or down—a technique known as portamento.

12.Neck Strap Clip: Connect the included neck strap here.

13.Program Button: Without touching any note keys, touch this screw to display the current Program (internal sound) in the display. You can then press the Hold Button to move to the next Program or press the Interval Button to move to the previous Program.

14.Pitch-Bend Plates: Touch the upper or lower plate while playing a note to raise or lower its pitch, respectively. You can adjust the position of these plates by loosening their screws.

15.FX (Effects) Button: Press and hold this button and then use the Hold Button and Interval Button to select Reverb (rb), Chorus (ch), or Delay (dL). You can then release the FX Button and use the Hold Button to increase the effect level or press the Interval Button to decrease the effect level.

16.Level Button: Press this button to show the Main Output level in the display. You can then press the Hold Button to increase the level or press the Interval Button to decrease the level.

17.Bank Button: Press this button to switch between the bank of Preset Programs and the bank of User Programs. The Preset LED and User LED next to it will indicate which bank is selected, Preset or User.

18.Save Button: Press this button to enter Save Mode. The "destination" User Program number will then blink in the display. Use the Hold Button and Interval Button to select the User Program number you want to save to, and press the Save Button again to save the Program, or press any other button to cancel the operation.

19.Wireless Switch: Selects whether or not the EWI5000 is "paired" with the wireless receiver. To do this, connect the wireless receiver to a USB port on your computer. (Alternatively, connect the receiver to the included USB power adapter, and connect the adapter to a power outlet.) The receiver's Pair LED will flash. With the EWI5000 powered on, set this Wireless Switch to On. It will automatically pair to the wireless receiver. When it is paired to the wireless receiver, the wireless receiver's Pair LED and the EWI5000's Preset LED or User LED (next to the Bank Button) will both light solid.

Note: If the connection is lost, you can manually pair the EWI5000 to the receiver by pressing the receiver's Pair Button and then pressing the EWI5000's Power Button once.

20.Power: Press and hold this button for a full second to power the EWI5000 on or off.

21.MIDI Out: Use a standard five-pin MIDI cable to connect this port to an external sound module's MIDI In port, allowing you to use the EWI5000 as a MIDI controller for that sound module.

22.Phones: Connect headphones (optional, sold separately) here with a stereo 1/8" (3.5mm) cable.

23.Battery Compartment: Use a standard Phillips-head screwdriver (not included) to remove the battery compartment cover, install the battery, and re-secure the cover.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents User Guide Table of Contents EWI About the EWI5000 SupportPower the EWI5000 Hold the EWI5000 ProperlyTo play EWI5000s audio wirelessly ConnectTo play EWI5000s audio through headphones To play EWI5000 as a wired Midi controllerTips PlayGlide Plate Standard Pitch Pitch-Bend Up Pitch-Bend Down Features Page Page Breath Adjusting Sound ParametersFilter BiteReverb FineChorus Adjusting Sensors To adjust the Note DelayTo adjust the breath sensor Breath SensorPage To adjust the bite sensor Bite SensorPage To adjust the pitch-bend plates Pitch-Bend PlatesGlide Plate To set the function of the glide platePage Calibrating Sensors Key Delay Note Keys and Program ButtonTo calibrate the note keys and Program Button To calibrate the breath sensor To calibrate the glide plate To calibrate the pitch-bend plates Midi Channel Assigning ControlsTo set the Midi Channel Hold Button Off The Hold Button will be disabledTo set the function of the Hold Button Page Interval Button To set the function of the Interval ButtonPage Managing Programs Using the Program ButtonSelecting Programs Using the Note Keys Using the Hold Button and/or Interval ButtonRelease the Program Button Saving Programs An External Midi Sound Module or SoftwareTo save a Program Reverb Using Effects FXTo edit the Reverb effect Chorus DelayTo edit the Delay effect To edit the Chorus effectTo select a fingering mode Fingering ModesTo update the EWI5000s software Restoring Default SettingsUpdating the Firmware Fingering Charts K1 K2 K3 K4 K5 K6 K10 K11 K12EWI Saxophone Flute Oboe EVI EVI ReversedSetup Mode Menu StructuresMenus Values Menus Values FX Effects Technical Specifications Trademarks and LicensesAkaipro.com
Top Page Image Contents