Akai manual Power the EWI5000, Hold the EWI5000 Properly

Page 5

Getting Started

Important

Before operating the EWI5000, please note the following:

•Do not bite the mouthpiece too hard—this can damage the vibrato sensor. Use the mouthpiece cover after using or while carrying the EWI5000.

•Always touch the grounding plate and octave rollers when playing. These are sensors which use the performer's body as the ground.

•Keep the mouthpiece clean before, during, and after using the EWI5000. You can clean its outer surface with disinfectant alcohol.

1. Power the EWI5000

The EWI5000 is powered by a rechargeable battery. Please note the following about using it:

•Installation: Use a standard Phillips-head screwdriver (not included) to remove the EWI5000's battery compartment cover below the Phones output, install the battery, and re-secure the cover.

•Charging: Use the included USB cable to connect the EWI5000's USB port to either (A) the included USB power adapter, connected to a power source or (B) an available USB port on your computer (powered on). You can charge the battery while using the EWI5000. While charging, a dot will flash in the EWI5000's display.

•Battery life: Check the battery life by pressing and holding the Level Button and then pressing and holding the FX Button. The amount of battery life (00–99) will appear in the display.

•Low-battery warning: When the battery power is low, the Preset LED or User LED will blink to indicate that you should charge the battery.

•Auto-power-off:If the EWI5000 detects no activity for approximately 10 minutes, it will power off automatically. In general, though, power off the EWI5000 to preserve its battery life when you are not using it.

2. Hold the EWI5000 Properly

1.Secure the neck strap to the EWI5000's neck strap mount.

2.Place the strap around your neck and hold the EWI5000 in the

same way you would hold a saxophone or clarinet, with the instrument vertically right in front of you.

3. When playing, place your left thumb on the octave rollers in the back, and place your right thumb on the grounding plate between the pitch-bend plates. This will ensure the best possible conductivity and performance of the instrument.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents User Guide Table of Contents EWI Support About the EWI5000Hold the EWI5000 Properly Power the EWI5000Connect To play EWI5000s audio wirelesslyTo play EWI5000 as a wired Midi controller To play EWI5000s audio through headphonesGlide Plate Standard Pitch Pitch-Bend Up Pitch-Bend Down PlayTips Features Page Page Filter Adjusting Sound ParametersBreath BiteChorus FineReverb To adjust the Note Delay Adjusting SensorsBreath Sensor To adjust the breath sensorPage Bite Sensor To adjust the bite sensorPage Pitch-Bend Plates To adjust the pitch-bend platesTo set the function of the glide plate Glide PlatePage To calibrate the note keys and Program Button Key Delay Note Keys and Program ButtonCalibrating Sensors To calibrate the breath sensor To calibrate the glide plate To calibrate the pitch-bend plates To set the Midi Channel Assigning ControlsMidi Channel To set the function of the Hold Button Off The Hold Button will be disabledHold Button Page To set the function of the Interval Button Interval ButtonPage Selecting Programs Using the Program ButtonManaging Programs Release the Program Button Using the Hold Button and/or Interval ButtonUsing the Note Keys To save a Program An External Midi Sound Module or SoftwareSaving Programs To edit the Reverb effect Using Effects FXReverb To edit the Delay effect DelayChorus To edit the Chorus effectFingering Modes To select a fingering modeUpdating the Firmware Restoring Default SettingsTo update the EWI5000s software K1 K2 K3 K4 K5 K6 K10 K11 K12 Fingering ChartsEWI Saxophone Flute Oboe EVI Reversed EVIMenu Structures Setup ModeMenus Values Menus Values FX Effects Trademarks and Licenses Technical SpecificationsAkaipro.com
Top Page Image Contents