Majestic Appliances LDVR1 Locating Your Fireplace, Clearance to Combustibles, Mantels

LDVR Series Direct Vent Gas Fireplace

Locating Your Fireplace

E	A	B
Y
	C	X
D
Y	X	B
	F
		LU584-R
Fig. 2 Locate gas fireplace.
A) Flat on wall	B) Cross corner	C) **Island
D) *Room divider	E) *Flat on wall corner	F) Chase installation
Y) 6” minimum

NOTE: (Fig. 2)

**Island (C) and Room Divider (D) installation is possible as long as the horizontal portion of the vent system (X) does not exceed 20’ (610cm). See details in Venting Section.

*When you install your fireplace in(D) Room divider or (E) Flat on wall corner positions (Y), a minimum of 6” (153mm) clearance must be maintained from the perpendicular wall and the front side edge of the fireplace.

Refer to (Y) in Figure 2.

Clearance to Combustibles

Top of Unit to Ceiling	36” (914 mm)
Appliance
Top	0” (0 mm)
Bottom	0” (0 mm)
Side	0” (0 mm)
Back	0” (0 mm)
Venting
Concentric sections of DV Vent
Top, bottom & sides	1” (25 mm)
Rear Vent Applications:
Top	2” (50 mm)
Sides and Bottom	1” (25 mm)
Flex Vent	7/8” (22 mm)

Mantels

The height that a combustible mantel is fitted above the fireplace is dependent on the depth of the mantel. This also applies to the distance between the mantel leg (if fitted) and the fireplace.

For the correct mounting height and widths refer to Figs. 3a and 3b, and the following Mantel Charts.

The fitting of a bay window trim kit does not effect the distances and reference points referred to in the diagram and chart.

Noncombustible mantels and legs may be installed at any height and width around the appliance.

When using paint or lacquer to finish the mantel, such paint or lacquer must be heat resistant to prevent

discoloration.

6

V

W

X

Y

Z

									3/4” (19 mm) Scribe
									Moulding for use with
			A B	C D		E			CFM Cabinets
									Fireplace
									Top Louvre
									Assembly
									Top of Combustion
									Chamber
CFM146
			Mantel Chart
	Mantel Shelf								Mantel from Top
Ref.	or Breast Plate			Ref.			of Combustion Chamber
		Depth			36/39/43 LDVR					33LDVR
V	10”	(254 mm)		A		17”		(432 mm)		16¹⁄₂” (419 mm)
W	8”	(203 mm)		B		15”		(381 mm)		14¹⁄₂” (368 mm)
X	6”	(152 mm)		C		13”		(330 mm)		12¹⁄₂” (318 mm)
Y	4”	(102 mm)		D		11”		(279 mm)		10¹⁄₂” (267 mm)
Z	2”	(51 mm)		E		9”		(229 mm)		8¹⁄₂” (216 mm)

Fig. 3a Combustible mantel minimum installation.

		3/4” (19 mm) Scribe
		Moulding for use with
		CFM Cabinets
Black		J	I H
				G
Surround
Face	Mantel			F
CFM164a	Leg
Side of		MLK
Combustion Chamber		N
		O

								CFM170
				Mantel		Mantel Leg FromSide
	Ref.		Leg Depth		Ref.	of Comb. Opening
	F		10”	(254 mm)	K	11¹⁄₂”	(292 mm)
	G		8”	(203 mm)	L	9¹⁄₂”	(241 mm)
	H		6”	(152 mm)	M	7¹⁄₂”	(191 mm)
	I		4”	(102 mm)	N	5¹⁄₂”	(140 mm)
	J		2”	(51 mm)	O	3¹⁄₂”	(89 mm)
Fig. 3b		Combustible mantel leg minimum installation.
							10007317