Vanguard Managed Solutions Essential Accessories for Your Vanguard Fireplace

Page 38

®

DIRECT-VENT FIREPLACE

ACCESSORIES

Purchase these fireplace accessories from your local dealer. If they can not supply these accessories, call DESA International’s Sales Department at 1-800-432-2382. for information. You can also write to the ad- dress listed on the back page of this manual.

BRASS PERIMETER TRIM KIT - D9037(37")/GA6091(41") (Not Shown)

Optional three sided brass trim kit covers unfinished edges around fireplace. Provides a finished appearance with the class of brass.

BRASS LOUVER KIT

D6037(37")

D6041(41")

(Not Shown)

These louvers will give your fireplace an elegant look and allows you to customize your fireplace. They easily replace the stan- dard black louvers by screwing into place.

BRICK LINER

D8037A(37")

D8041(41")

(Not Shown)

This brick liner adds a touch of style to your direct-vent fireplace and comes with easy to follow instructions for installation.

WALL MOUNT ON/OFF SWITCH KIT - GWMS2

Allows the fireplace to be turned on and off with a wall switch.

CLEANING KIT - GCK

(Not Shown)

Your direct-vent gas appliance requires regu- lar cleaning and maintenance to prevent performance problems. This kit gives you the tools and instructions to make it easy to clean all critical areas of your appliance.

CABINET MANTEL WITH SQUARE LEG STYLING - UNFINISHED GM501U(37")/ GM103U(41")

For use with all models. This birch-veneer mantel is unfinished and ready to stain or paint. Complete assembly instructions are in- cluded along with a three-sided brass trim kit.

DECORATIVE BRASS STRIP KIT - D5037(37")/D5041(41") FOR BDV ONLY (Not Shown)

These strips have a magnetic backing which makes installation and removal quick and easy. They are designed to go at the top and bottom of the glass door on BDV units. Note: Remove the plastic film covering on strips before installing on fireplace.

38

106497

Image 38
Contents Check Local Codes Prior to Installation OWNER’S Operation and Installation ManualFor Your Safety MBDV37 and MBDV41Safety Information Glossary Terms Product FeaturesLocal Codes Product IdentificationLocation and Space Requirements PRE-INSTALLATION PreparationClearances Framing and FinishingPRE-INSTALLATION Preparation General Venting Location of Vent TerminationGeneral Venting Installation Planning Venting InstallationInstallation Precautions Installation for Horizontal Termination Installing Vent System in a ChaseVent Opening Requirements Horizontal Termination Configurations Horizontal VentingVenting with Two 90 Elbows Cathedral Ceiling Installation Installation for Vertical TerminationFlat Ceiling Installation Connect a section of pipe and extend up through the holeVertical Termination Configurations Venting with One 90 ElbowVertical Rigid Venting Configuration Using Two 90 Elbows Vertical VentingVanguard Rigid Venting High Altitude InstallationParts Lists for Venting Kits and Components Vanguard Flexible VentingCheck GAS Type Fireplace InstallationElectrical Hookup for Blower Accessory Number Description Available from Desa InternationalSome Models Have Blower Assembly Preinstalled Blower Assembly and OperationInstalling GA3700 Blower Open lower louver panel or remove for easier accessInstalling Receiver Wall Switch InstallationWireless HAND-HELD Remote Control Ghrc Series Installation Installing GAS Piping to Fireplace Location Installation Items NeededInstallation Items Needed Connecting Fireplace to GAS SupplyGAS Supply Testing Pressure Testing Gas Supply Piping SystemPressure Testing Fireplace Gas Connections Close equipment shutoff valve see Fig- ureREMOVING/REPLACING Glass Door Removing/Replacing Glass DoorReplace glass door see Installing Optional Brick Liner D8037A/D8041Tighten all bracket screws Installing LOGS, Lava Rock and Glowing Embers Fireplace Models MBDV37 and MBDV41Operating Guidelines and Maintenance Instructions Operating Fireplace To Appliance For Your Safety Read Before LightingManual Lighting Procedure Lighting To Turn OFF GASRemote Operation Pilot AssemblyInspecting Burners Operating BlowerPilot and Burners Cleaning and MaintenanceGlass Door LogsBefore YOU Begin Main Burner Orifice and Pilot OrificeGAS Control Valve Conversion Final PreparationTroubleshooting Observed Problem Possible CausePilot’s millivoltage Trying to light the fireplaceParts, OrificePane/LP or natural gas company Delayed ignition burner Manifold pressure is too lowBurner is lit Glass soots Flame impingement on logsGas leak. See Warning statement AboveService Hints Replacement Parts Wiring DiagramTechnical Service SpecificationsIllustrated Parts Breakdown MBDV37 MBDV41Parts List DIRECT-VENT Fireplace MBDV37 MBDV41Cleaning KIT GCK AccessoriesWall Mount ON/OFF Switch KIT GWMS2 Brass Louver KIT106497 Warranty Information