Desa (V)T32EP-A SERIES, (V)T32EN-A SERIES Right outside, Wiring Diagram Decal 12 in Front Blower

Page 18

Fireplace

Installation

Continued

3.Place the blower against the lower rear wall of the firebox outer wrapper with the exhaust port directed upward. The blower will fit inside the back opening and be held in position against the back wall by the magnets (see Figure 25, page 17).

4.Be certain that all wire terminals are securely attached to terminals on blower motor and that the screw retaining the green ground wire is tight.

5.Mount speed control box to switch bracket by placing the plastic control shaft forward through the opening in the switch bracket (see Figure 26).

6.While supporting speed control, secure control shaft with lock nut by pushing and turning lock nut with pliers clockwise until it is tight against front panel. Place control knob pro- vided on shaft.

7.Turn on power to duplex outlet if previ- ously turned off per the warning in column 2, page 17.

8.Plug in blower power cord.

a.If your firebox is installed as a free- standing unit with an accessory mantel, determine whether the power cord will exit the left side or the right side of the firebox. Route power cord through exit hole and plug the power cord into a wall receptacle near the firebox.

b.If your firebox installation is recessed and/or pre-wired, plug the power cord into the duplex outlet provided. Refer to your firebox owner’s manual for instruc- tions on wiring the duplex outlet.

CAUTION: Never touch the blower wheel while in operation.

9.Check to make sure that the power cord is com- pletely clear of the blower wheel and that there are no other foreign objects in blower wheel. Turn blower on and check for operation. Turn blower off by turning knob fully counterclock- wise before continuing.

10.Peel off the backing paper and stick the sup- plied wiring diagram decal on the firebox bot- tom approximately 12" in front of the blower (see Figure 27).

Speed

Switch Control

BracketBlower

Plug-In

 

Control

Duplex Outlet

Locknut

(Located

Control

Shaft

underneath

Knob

 

firebox floor

 

 

against lower

 

 

right outside

 

 

wall)

Figure 26 - Attaching Speed Control to

Firebox

Wiring Diagram

Decal 12" in Front

of Blower

Figure 27 - Location of Wiring Diagram Decal (Model May Vary From Illustration)

Model BKT Installation

Note: When installing the BKT thermostati- cally-controlled blower, you must first secure the thermal switch bracket to the blower if it has not already been factory installed.

1.Place the green ground wire with ring terminal between the bottom hole on the thermal switch bracket and the top ear hole on the blower assembly. Insert the phillips screw into all three pieces and tighten securely (see Figure 28, page 19).

2.Connect wire harness and power cord ter- minals. Connect the blue jumper wire to the blower motor terminal and the right side ter- minal of the thermal switch. Connect the black wire to the left side of the thermal switch and the white wire to the other remaining blower motor terminal.

Note: The power cord outer insulation sleeve may have to be stripped slightly to allow enough wire length to reach and make all connections. DO NOT trim excessive length away. Just enable enough to make all connections securely.

18

www.desatech.com

116647-01B

Image 18
Contents What to do if YOU Smell GAS Table of Contents Safety InformationSafety Information Product Features Product IdentificationLocal Codes Clearances Pre-Installation PreparationLocation and space requirements Flush with a wallFraming and finishing Location of Termination Cap Termination CAP AIR Supply Inlet GAS MeterVenting Installation Instructions Installation PrecautionsCenter Installation PlanningMale Slots Female Locking Lugs HoleVent Cap Wood Screw Noncombustible ExteriorVenting Installation Square TerminationHorizontal H 53 3/4 min Wall Firestop Elbow43 3/4 min None 65 3/4 minVertical V Horizontal H Venting with Two 90 ElbowsMin Max 12 max 18 max 20 max Elbow Min Max 12 max 18 max Elbow 20 maxRoof Flashing Wall Strap Elbow Ceiling Firestop Installation for vertical terminationFlat Ceiling Installation If area above is aMin Max 20 max Elbow Venting with One 90 Elbow Vertical V Horizontal HMin Max 12 max 18 max 20 max Vertical Venting High Altitude InstallationParts list for venting kits and components = 40 max ElbowModel BK Installation Fireplace InstallationInstalling optional blower accessory Check GAS TypeWiring Diagram Decal 12 in Front Blower Model BKT InstallationRight outside Blower Wiring Diagram Blower Model BKTInstalling Gas Piping to Fireplace Location Installation Items NeededConnecting Fireplace to GAS Supply Checking GAS ConnectionsRed Surface Test Pressures Equal To or Less Than Psig 3.5 kPa Pressure Testing Fireplace Gas ConnectionsRemoving/Replacing Glass Door Removing Louver PanelsInstalling Optional Brick liner Model BL32D Cleaning Glass DoorRemoving Glass Door Installing logs, lava rock and glowing embers Left Side Brick PanelWall Switch Installation Optional Remote control Installation model WRCOperating Fireplace Wiring DiagramFor Your Safety Read Before Lighting Lighting InstructionsOperating optional blower accessory To Turn OFF GAS To ApplianceOptional Remote Operation Inspecting Burners Cleaning MaintenancePilot Assembly Burner Flame PatternPilot and burners LogsVenting system Troubleshooting Observed Problem Possible Cause RemedyGas leak. See Warning Checking Gas ConnectionsTechnical Service Replacement PartsService Hints SpecificationsAccessories Remote Control KIT WRCIllustrated Parts Breakdown 22-1 1141814123 21171 24353 24460 22-2109 Electronic Valve Propane/LP 116647-01B 116647-01B Warranty Information Keep this WarrantyLimited Warranty DIRECT-VENT Fireplace