TROUBLESHOOTING
Continued
OBSERVED PROBLEM | POSSIBLE CAUSE | REMEDY | |||
|
|
|
|
| |
ODS/pilot lights but flame goes | 1. Control knob not fully | 1. | Press in control knob fully | ||
out when control knob is re- |
| pressed in | 2. | After ODS/pilot lights, keep con- | |
leased | 2. Control knob not pressed in | ||||
| 3. | long enough | 3. | trol knob pressed in 30 seconds | |
| Equipment shutoff valve not | Fully open equipment shutoff | |||
| 4. | fully open | 4. | valve | |
| Pilot flame not touching | A) Contact local natural or | |||
|
| thermocouple, which allows |
| propane/LP gas company | |
|
| thermocouple to cool, caus- |
| B) Clean ODS/pilot (see | |
|
| ing pilot flame to go out. This |
| ||
|
| problem could be caused by |
| Cleaning and Maintenance, | |
|
| one or both of the following: |
| page 21) or replace ODS/pilot | |
|
| A) Low gas pressure |
| assembly | |
|
| B) Dirty or partially clogged |
|
|
|
| 5. | ODS/pilot | 5. | Hand tighten until snug, then | |
| Thermocouple connection | ||||
| 6. | loose at control valve | 6. | tighten 1/4 turn more | |
| Thermocouple damaged | Replace pilot assembly | |||
| 7. | Control valve damaged | 7. | Replace control valve | |
|
|
|
|
| |
Burner does not light after ODS/ | 1. Inlet gas pressure is too low | 1. | Contact local natural or pro- | ||
pilot is lit | 2. | Burner orifice(s) clogged | 2. | pane/LP gas company | |
| Clean burner(s) (see Cleaning | ||||
|
|
|
| and Maintenance, page 21) or | |
| 3. | Thermopile leads disconnected | 3. | replace burner orifice(s) | |
| Reconnect leads (see Wiring | ||||
| 4. | or improperly connected | 4. | Diagram, page 22) | |
| Burner will not come on in | Replace battery in transmitter | |||
|
| remote position |
| and receiver | |
|
|
|
|
| |
Delayed ignition of one or both | 1. Manifold pressure is too | 1. | Contact local natural or pro- | ||
burners | 2. | low | 2. | pane/LP gas company | |
| Burner orifice(s) clogged | Clean burner(s) (see Cleaning | |||
|
|
|
| and Maintenance, page 21) or | |
|
|
|
| replace burner orifice(s) | |
|
|
|
|
| |
Burner backfiring during | 1. Burner orifice is clogged or | 1. | Clean burner (see Cleaning | ||
combustion |
| damaged |
| and Maintenance, page 21) or | |
| 2. | Damaged burner | 2. | replace burner orifice(s) | |
| Replace damaged burner | ||||
| 3. | Gas regulator defective | 3. | Replace gas regulator | |
|
|
|
|
| |
Slight smoke or odor during initial | 1. Not enough air | 1. | Check burner for dirt and | ||
operation |
|
|
| debris. If found, clean burner | |
|
|
|
| (see Cleaning and Mainte- | |
| 2. | Gas regulator defective | 2. | nance, page 21) | |
| Replace gas control | ||||
| 3. | Residues from manufacturing | 3. | Problem will stop after a few | |
|
| processes and logs curing |
| hours of operation | |
24 | www.desatech.com |