Hearth and Home Technologies Grand-XT, Supreme-XT manual Positioning the Logs, Shutter Settings

Page 26

Installing the Insert (continued)

Step 7

Installing Logs and Ember Material

Positioning the Logs

If the gas logs have been factory installed they should not need to be positioned.

If the logs have been packaged separately, refer to the installation instructions that accompany the logs. Save the log instructions with this manual.

If sooting occurs, the logs might need to be repositioned slightly to avoid excessive flame impingement.

Shutter Settings

 

NG

LP

___________________________________________

Supreme-XT

3/8”

Full Open (3/4”)

___________________________________________

Grand-XT

1/2”

Full Open (3/4”)

 

 

 

Placing the Ember Material

One bag of ember material is shipped with this gas appliance:

The bag labeled Glowing Ember (050-721) is standard glowing ember material.

To place the ember material:

Remove the trim door by pulling out the bottom and lift- ing to unhook.

Unlatch the latches at the bottom of the glass door.

Remove the glass door from the unit.

Cover the top of the burner with a single layer of ember material (see Figure 12).

Save the remaining ember materials for use during fire- place servicing.

Replace the glass door. Slide the top tabs on the glass door into the slots on top of the firebox. On the Grand- XT slide the top tabs under the top spring latches. Ro- tate the bottom of the glass door toward the firebox with slight upward pressure. Latch the bottom spring latch securely onto the bottom glass door tabs.

Replace the trim door.

Installation de la cassette (suite)

Étape 7

Installation des bûches et des braises

Mise en place des bûches

Si les bûches à gaz ont été placées en usine, elles n’ont pas besoin d’être replacées.

Si les bûches ont été emballées séparément, reportez-vous aux instructions d’installation qui accompagnent les bûches.

Conservez les instructions relatives aux bûches avec ce manuel.

En cas de formation de suie, il est possible que les bûches aient besoin d’être légèrement repositionnées afin d’éviter un empiètement excessif sur les flammes.

Fixations d’obturateur

 

GN

PL

___________________________________________

Supreme-XT

9.5 mm

Plein ouvert (19 mm)

___________________________________________

Grand-XT

12.7 mm

Plein ouvert (19 mm)

 

 

 

Mise en place des braises

Un sac différents de braises sont livrés avec cet appareil à gaz :

Le sac étiqueté Glowing Ember (050-721) est une imi- tation standard de braises incandescentes.

Pour mettre les braises en place :

Démontez la porte de garniture en tirant sa partie inférieure et soulevez-la pour la dégager des crochets.

Ouvrez les verrous en bas de la porte en verre.

Retirez la porte en verre de l’appareil.

Couvrez le dessus du brûleur d’une seule couche de braises, (voir Figure 12).

Conservez le reste des braises afin de pouvoir les utiliser lors de l’entretien du foyer.

Replacez la porte en verre. Insérez ensuite les languettes du haut de la porte en verre dans les fentes situées en haut du foyer. Pour le modèle Grand-XT, faites glisser les languettes du haut sous les verrous à ressort du haut. Tournez le bas de la porte en verre en direction du foyer en appliquant une légère pression vers le haut. Engagez fermement le verrou à ressort du bas sur les languettes du bas de la porte en verre.

Replacez la porte de garniture.

26

Image 26
Contents Guide d’installation Safety and Warning Information Page Table of Contents Service Parts 11 8GRAND-XT SUPREME-XT Grand-XT, Supreme-XT Grand-XT Supreme-XT Appliance Certification 1Approvals and Codes Approval Listing and CodesHomologations et codes Homologation de l’appareilPre-installation Preparation Préparation avant l’installationGetting Started Comment débuter suiteGetting Started Diagram All models Insert Diagram 3Installing the Insert Step Installing the Vent System Raccord du conduit d’air Connecting the Vent PipeFront of the unit Installing the Insert Installation de la cassette suiteTermination CAP Installing the Insert Installation de la cassette suite Step Étape Gas Control Systems Systèmes de commande de gaz Gas Controls Systems Systèmes de Commande de gazInstalling the Insert Step Gas Supply Line Installation de la cassette suite Étape 4 Conduit à gazPression Gaz naturel Propane Installing the Insert Step Gas Pressure RequirementsPressure Natural Gas Propane Installing the Insert Step Wiring the Fireplace Installing the Insert Installation de la cassette suite Fan Wiring DiagramPlacing the Ember Material Shutter SettingsPositioning the Logs Mise en place des bûchesGlass Assembly Porte en verre Placement Mise en place des Ember Material BraisesAvertissement Lors DE LA Finition DE Remarque Placez LES Trois Morceaux Vérifiez qu’il n’y ait pas d’éléments défectueux Installing the Insert Step Before Lighting the ApplianceDouble-check for faulty components Entretien et service de votre appareil After the InstallationAprès l’installation Step Lighting the ApplianceSive cleaners ’essayez PAS de nettoyer la Cleaning Glass DoorTempt to clean the door when Checking Vent System Vérification du système d’évacuation