Hearth and Home Technologies CASTLEWOOD 42 Complete the Enclosure, Install the Termination Cap

Page 17

6Complete the Enclosure

A. Chimney Termination

Chimney Termination Requirements (see Fig- ure 6.1)

•Must have a cap approved and listed for this fireplace system

•Must not be located where it will become plugged by snow or other material

•Must terminate at least 3ft (914 mm) about the roof and at least 2 ft (610mm) above any portion of the roof within 10 ft. (305mm)

•Must be located away from trees or other structures

WARNING

Fire Risk

•Must maintain 2 in. (51 mm) air clearance to insulation and other combustible materials.

C. Install the Termination Cap

Note: To protect against the effect of corrosion on those parts exposed to the weather, the termination cap can be painted with a rust-resistant paint.

WARNING

Fire Risk

•The minimum overlap of cap to pipe MUST be met or chimney may separate from cap.

Separation allows sparks, heat and embers to escape.

Install the chimney sections up through the chase enclosure and refer to termination cap instructions.

NOTE: TR11/TR444 Round Termination Cap and TR11T/ TR442 Round Telescoping Termination Cap not recom- mended for Installations less than 20 feet.

B. Chase Top

A metal chase top is required to seal the top of the chase around the chimney pipe. The top should include a turn- down and drip edge to prevent water from seeping into the chase. Provide a 1/8 in. (3 mm) gap around the flue pipe and slope the top downward away from the penetration.

ST1175/ST475 Square Termination Cap

•All seams must be caulked to prevent leaks.

•A chase installation must use a chase top. Chase tops are available from your HHT dealer or may be field constructed.

•Attach the chase top to the top of the chase.

2 in. (51 mm) Collar on Chase Top

Slope Downward

Turn-down

Drip Edge

.018 (26 ga) min. Galvanized Chase Top

Figure 6.1 Field Constructed Chase Top Specification

Flange

Termination Cap

Collar

2 in. (51 mm)

Minimum Height

Chase Top

Chimney

Pipe

Place waterproof caulk or sealer under each flange of the termination cap and on top of each screw to help prevent leaks.

The last section of pipe must stop between 2 in. (51

mm)above the top of the chase and 4 3/4 in. (121

mm) below the top of the chase.

2 in. (51 mm) maximum

4 3/4 in. (121 mm) maximum

Chase

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)

Figure 6.2 Installing an ST1175/ST475 Square Termination Cap

Outdoor Lifestyles by Hearth & Home Technologies Inc. • 4070-300 Rev C • 4/11

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Fire Risk Hot glass will cause burnsNumber Listing Label Information/LocationGrate Table of Contents Appliance Certification Listing and Code ApprovalsNot intended for use as a primary heat source Do not overfireGetting Started Grate Inspect Fireplace and ComponentsFirescreen Cooling AirFraming and Clearances Freestanding Installations see FigureSelecting Fireplace Location Exterior Walls see FigureFreestanding Installation Clearances Frame the Fireplace Sidewalls/SurroundsChimney Requirements Secure the Fireplace Position the Fireplace Installation of FireplaceLevel the Fireplace Place the Protective Metal Hearth StripsInstall Cooling Air Hoods Height of Chimney Components Chimney AssemblyAssemble the Chimney Sections Using Offsets/Returns Complete the Enclosure Install the Termination CapChase Top ST1175/ST475 Square Termination CapTCT1175 Terra Cotta Cap Installing a TCT1175 Square Termination CapInstall Side Molded Brick Panel Installation of Molded Brick PanelMortar Optional Grate Install ScreensGas Log/Lighter Provisions AccessoriesGas Code, Ansi Z223.1 Asphyxiation Risk= 1/k x inches of thickness FinishingHearth Extension Non-combustible Raised Hearth Extension FramingFraming Material Equivalent insulationFlush Hearth Extension Framing Non-combustible SealantUse only non-combustible framing material below standoffs Finishing MaterialStandoffs MantelGeneral Information Operating InstructionsFire Risk Smoke Risk Clear Space Near the FireplaceGlass Doors Firewood Wood FuelStarting a Fire Diagnostics and Problem Solving TroubleshootingDisposal of Ashes Chimney Inspection/Cleaning Maintenance and Servicing the FireplaceWhen cleaning glass door Maintenance Task ListClean Chimney FireReference Materials Fireplace DimensionsOptional Components Catalog # Chimney Components330 mm 51 mm 15-3/4 400 mm Termination capsODCASTLEWD-42 Service Parts ListHerringbone Molded Brick Panel At DepotTraditional Molded Brick Panel Warranty Coverage This warranty is void if Limited WarrantyRO N a CO ISD D

CASTLEWOOD 42 specifications

Hearth and Home Technologies has consistently been at the forefront of innovative fireplace solutions, and the CASTLEWOOD 42 is no exception. This exquisite linear gas fireplace is a perfect blend of modern design and advanced technology, making it a sought-after choice for homeowners looking to elevate their living spaces.

One of the standout features of the CASTLEWOOD 42 is its impressive 42-inch width, which allows it to serve as a stunning focal point in both contemporary and traditional interiors. The fireplace is designed with a sleek, clean appearance, featuring large viewing glass and a minimalist frame that creates an unobstructed view of the mesmerizing flames. With its flush-mount design, the CASTLEWOOD 42 can be easily incorporated into a variety of wall configurations, making it versatile enough for any room.

The CASTLEWOOD 42 is powered by advanced Direct Vent technology, ensuring efficient and safe operation. This system allows for the expulsion of combustion gases outside the home, while simultaneously drawing in fresh air for combustion. As a result, the fireplace operates cleanly, providing warmth without compromising indoor air quality. Additionally, the unit is designed to produce up to 30,000 BTUs, delivering sufficient heat to keep spaces cozy during chilly weather.

One of the most impressive aspects of the CASTLEWOOD 42 is its customizable options. Homeowners can choose from a variety of decorative media, such as glass rocks, driftwood, or ceramic logs, to personalize the fireplace and match their decor. The included LED accent lighting enhances the ambience by providing a soft glow that highlights the decorative elements, creating a warm and inviting atmosphere.

Remote control capability is another notable feature of the CASTLEWOOD 42, allowing users to effortlessly adjust the flame height and heat output from the comfort of their couch. Add-on options such as wall-mounted control panels or smartphone integration elevate convenience, ensuring that comfort is just a click away.

The CASTLEWOOD 42 not only excels in aesthetics and functionality but also adheres to high safety standards. With features like tempered glass and a secure venting system, it ensures peace of mind for families. Overall, the Hearth and Home Technologies CASTLEWOOD 42 stands as a testament to quality craftsmanship and innovative design, making it a brilliant addition to any home. Its combination of style, efficiency, and technology proves that fireplaces can be both functional and beautiful.
Top Page Image Contents