Hearth and Home Technologies CASTLEWOOD 42 owner manual Install Screens, Mortar Optional Grate

Page 20

D. Install Screens

•Lay one screen panel flat and slide the round end of the rod through the rings starting at the handle side of the screen. Leave the last ring off the rod.

•Insert the rod through the hole in the bracket. Slip the last ring over the rod on the other side of the bracket.

•Fasten the flat end of the screen rod back in place us- ing the screw removed earlier.

•Repeat for the other screen panel

Round end of Rod through rings, then into Screen Rod Clip

 

Top of Fireplace

OpeningFireplaceof

Rod Screen

Clip

 

Center

Inside

Firebox

 

E.Mortar (Optional)

F.Grate

•Install the grate If a gas log set is not going to be installed.

•Position the rear grate bar in the Grate Retainer

•Position the top of the grate retainer over the rear grate bar and fasten in place with screw provided.

The brick panels have been designed for installa- tion without the use of mortar being necessary. If the look of mortar is preferred, it is available and can be installed. Follow the directions on the container for mix- ing.

The mortar can be applied with a mortar bag or trowled on. Applying with mortar bag may be easiest and less messy. Clean sparingly as paint will rub off and may need to be touched up. Touch up paint is available as an accessory.

VERY IMPORTANT: Allow the mortar 72 hours to cure before operating the fireplace.

Mortar should be applied after finishing material is installed. Mortar will be applied between finishing materials and molded brick edges, bottom and sides.

The seam between finishing materials and firebox top must be sealed with non-combustible sealant.

The non-combustible finishing material across the top of fireplace opening will be even with lower edge of metal face.

Non-combustible finishing materials MUST overlap

side faces by 1 1/4 in. (32 mm) to cover the edges of the panels. Finished opening should be 38 x 42 in. (965 x 1067 mm) to allow for door installation.

The surface of the finished hearth extension and the surface of the hearth panel should be level.

Figure 7.5 Facing Materials and Mortar

20

Outdoor Lifestyles by Hearth & Home Technologies Inc. • 4070-300 Rev C • 4/11

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Hot glass will cause burns Fire RiskNumber Listing Label Information/LocationGrate Table of Contents Listing and Code Approvals Appliance CertificationNot intended for use as a primary heat source Do not overfireGetting Started Inspect Fireplace and Components GrateFirescreen Cooling AirFreestanding Installations see Figure Framing and ClearancesSelecting Fireplace Location Exterior Walls see FigureFreestanding Installation Clearances Sidewalls/Surrounds Frame the FireplaceChimney Requirements Installation of Fireplace Secure the Fireplace Position the FireplaceLevel the Fireplace Place the Protective Metal Hearth StripsInstall Cooling Air Hoods Chimney Assembly Height of Chimney ComponentsAssemble the Chimney Sections Using Offsets/Returns Install the Termination Cap Complete the EnclosureChase Top ST1175/ST475 Square Termination CapInstalling a TCT1175 Square Termination Cap TCT1175 Terra Cotta CapInstallation of Molded Brick Panel Install Side Molded Brick PanelInstall Screens Mortar Optional GrateAccessories Gas Log/Lighter ProvisionsGas Code, Ansi Z223.1 Asphyxiation Risk= 1/k x inches of thickness FinishingHearth Extension Raised Hearth Extension Framing Non-combustibleFraming Material Equivalent insulationNon-combustible Sealant Flush Hearth Extension FramingFinishing Material Use only non-combustible framing material below standoffsMantel StandoffsOperating Instructions General InformationFire Risk Smoke Risk Clear Space Near the FireplaceGlass Doors Wood Fuel FirewoodStarting a Fire Troubleshooting Diagnostics and Problem SolvingMaintenance and Servicing the Fireplace Disposal of Ashes Chimney Inspection/CleaningMaintenance Task List When cleaning glass doorClean Chimney FireFireplace Dimensions Reference MaterialsOptional Components Chimney Components Catalog #330 mm 51 mm Termination caps 15-3/4 400 mmService Parts List ODCASTLEWD-42Herringbone Molded Brick Panel At DepotTraditional Molded Brick Panel Warranty Coverage Limited Warranty This warranty is void ifRO N a CO ISD D

CASTLEWOOD 42 specifications

Hearth and Home Technologies has consistently been at the forefront of innovative fireplace solutions, and the CASTLEWOOD 42 is no exception. This exquisite linear gas fireplace is a perfect blend of modern design and advanced technology, making it a sought-after choice for homeowners looking to elevate their living spaces.

One of the standout features of the CASTLEWOOD 42 is its impressive 42-inch width, which allows it to serve as a stunning focal point in both contemporary and traditional interiors. The fireplace is designed with a sleek, clean appearance, featuring large viewing glass and a minimalist frame that creates an unobstructed view of the mesmerizing flames. With its flush-mount design, the CASTLEWOOD 42 can be easily incorporated into a variety of wall configurations, making it versatile enough for any room.

The CASTLEWOOD 42 is powered by advanced Direct Vent technology, ensuring efficient and safe operation. This system allows for the expulsion of combustion gases outside the home, while simultaneously drawing in fresh air for combustion. As a result, the fireplace operates cleanly, providing warmth without compromising indoor air quality. Additionally, the unit is designed to produce up to 30,000 BTUs, delivering sufficient heat to keep spaces cozy during chilly weather.

One of the most impressive aspects of the CASTLEWOOD 42 is its customizable options. Homeowners can choose from a variety of decorative media, such as glass rocks, driftwood, or ceramic logs, to personalize the fireplace and match their decor. The included LED accent lighting enhances the ambience by providing a soft glow that highlights the decorative elements, creating a warm and inviting atmosphere.

Remote control capability is another notable feature of the CASTLEWOOD 42, allowing users to effortlessly adjust the flame height and heat output from the comfort of their couch. Add-on options such as wall-mounted control panels or smartphone integration elevate convenience, ensuring that comfort is just a click away.

The CASTLEWOOD 42 not only excels in aesthetics and functionality but also adheres to high safety standards. With features like tempered glass and a secure venting system, it ensures peace of mind for families. Overall, the Hearth and Home Technologies CASTLEWOOD 42 stands as a testament to quality craftsmanship and innovative design, making it a brilliant addition to any home. Its combination of style, efficiency, and technology proves that fireplaces can be both functional and beautiful.
Top Page Image Contents